![](/images/new-backgrounds/1038099/3809987x1.webp)
VIDEO CONVERT
ANALOG VIDEO CONVERSION
The SR7001 is equipped to convert video signals for monitor output. Because of this, indifferent of the connection (VIDEO,
CONNECTION EXAMPLE
•When a monitor is connected to the HDMI MONITOR OUT terminal of the SR7001
VIDEO |
|
or |
|
or component |
|
or HDMI | HDMI |
• When a monitor is connected to the COMPONENT | TEMPORARILY TURNING OFF THE SOUND | ENGLISH | |||
VIDEO MONITOR OUT terminal of the SR7001 |
|
|
| ||
|
|
|
| ||
|
|
| OK |
|
|
VIDEO |
| PREV | LIP.SYNC | MUTE |
|
or | component |
|
| ||
MENU | GUIDE | EXIT |
| ||
or component |
| 1 | 2 | 3 |
|
|
| TEST | CH.SEL | SURR |
|
|
| 7.1CH | ATT |
| |
HDMI |
| 4 | 5 | 6 |
|
| DISP | OSD | SLEEP |
| |
|
| 7 | 8 | 9 |
|
UP-CONVERSION FROM ANALOG VIDEO
SIGNALS TO HDMI
The
Notes:
• HDMI video input is only output to the HDMI |
MONITOR OUT terminal of the SR7001. If |
connecting a playback device such as a DVD |
player to the HDMI input jack, connect the HDMI |
MONITOR OUT terminal of the SR7001 to a TV |
monitor. |
• This mode is unavailable for the REC out terminal. |
Notes:
•If the resolution of the component video signal input from the playback device is other than 480i/576i, 480p/576P, 1080i or 720p, images are not output from the HDMI MONITOR OUT terminal of the SR8001.
•If the resolution of the
•When a monitor is connected to the VIDEO or S- VIDEO MONITOR OUT terminals of the SR7001
Notes:
•The HDMI video signal input from the playback device is not output from the COMPONENT VIDEO MONITOR OUT terminal of the SR7001.
Notes of OSD menu system:
•The setup menu can be displayed through all video out terminals (“HDMI”, “COMPONENT”, “SVIDEO” and “VIDEO”).
•OSD information is output only to the VIDEO and
OSD information is also output when the video conversion feature is on and the video signal input to the VIDEO or
To temporarily silence all speaker outputs such as when interrupted by a phone call, press the MUTE button on the remote.
This will interrupt the output to all speakers and the
When the system is muted, the display will show “MUTE” .
Press the MUTE button again to return to normal operation.
USING THE SLEEP TIMER
| LIP.SYNC |
|
PREV |
| MUTE |
| GUIDE |
|
MENU |
| EXIT |
TEST | CH.SEL | SURR |
1 | 2 | 3 |
• This mode is unavailable for still picture, fast |
forward and reverse play on video component. |
• If, while attempting to use the video convert feature, |
the SR7001 cannot synchronize with the display |
device, “NO SIGNAL” appears on the monitor or |
noise is generated, this feature cannot be used. All of |
these signs are caused by equipment incompatibility; |
there is nothing wrong with the SR7001. |
If this occurs, set “VIDEO CONVERT” in the |
VIDEO |
or |
or component |
HDMI |
VIDEO
or
I/P CONVERT
The video circuit of the SR7001 is equipped with an I/P conversion feature.
When this feature is on, 480i/576i analog video signals (VIDEO,
7.1CH | ATT | |
4 | 5 | 6 |
DISP | OSD | SLEEP |
7 | 8 | 9 |
| THX |
|
CLEAR | 0 | MEMO |
“VIDEO SETUP” menu to “DISABLE”. Next, |
connect the video input signal to the display component |
via the MONITOR OUT terminal under VIDEO and |
the |
the MONITOR OUT terminal under |
• The video convert feature constantly monitors |
input video signals and determines whether to |
convert the input signals or not. However, some |
input video signals cannot be detected correctly. |
If this occurs, set “VIDEO CONVERT” in the |
“VIDEO SETUP” menu to “DISABLE”. |
• For optimal video performance, THX recommends |
setting the “VIDEO CONVERT” mode “DISABLE”. |
Notes:
•The HDMI video signal input from the playback device is not output from the VIDEO or
•If the resolution of the component video signal input from the playback device is other than 480i/576i, it is not output from the VIDEO or
to 480p/576p and progressively output to the COMPONENT VIDEO or HDMI MONITOR OUT terminals of the SR7001.
(For setting instructions, see page 35)
To program the SR7001 for automatic standby, press the SLEEP button on the remote.
Each press of the button will increase the time before shut down in the following sequence.
OFF 10
20
30
40
90 80
70
60
50
The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed.
When the programmed sleep time has elapsed, the unit will automatically turn off.
Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows “SLEEP OFF” and the SLEEP indicator will disappear.
41