Marantz SR7001 Auto Setup MultEQ Setup feature, Automatically optimizes settings, Listening area

ENGLISH	2-1 AUTO SETUP (MultEQ™ SETUP)
	The AUTO SETUP (MultEQ™ Setup) feature of
	the SR7001 measures sound characteristics of the
	speaker system and room where the receiver is used
	and automatically optimizes settings.
	The Audyssey MultEQ™ technology adopted by the
	SR7001 provides the best listening environment for
	multiple listeners.
	To do this, the AUTO SETUP feature measures a
	test tone emitted by each channel in a maximum of 6
	listening positions, using the supplied microphone.
	The measurement results are analyzed using an
	original algorithm and environmental settings are
	made to improve the sound characteristics of the
	listening area.
	To set up the speaker system (i.e., adjusting speaker
	distance, etc.) without using the AUTO SETUP feature,
	see “MANUAL SETUP” on page 31 of the manual.
	HOW TO PERFORM AUTO SETUP
	During measurement, the OSD menu displays the
	condition, therefore turn power to the monitor on.
	1. Connect the supplied microphone to the MIC
	jack on the SR7001.

2. Set the microphone in the listening position.

Notes:

•Measurement can be done in a maximum of 6 listening positions.

For the first measurement, set the microphone in the main listening position.

•Use a stand or tripod to position the microphone at ear height in the listening position.

•Remove any obstructions between the speakers and microphone.

•To use the internal subwoofer of the amp, set the volume to the middle point and set the crossover frequency to the highest.

•Duringmeasurement,stepawayfromthemicrophone and operate the SR7001 via the remote control unit from a position that is out of the path of the speaker sound.

•The test tone output from the speakers during measurement is loud. Be mindful of neighbors and watch out for small children.

3.Either press the MultEQ™ button on the front panel of the SR7001 or select “2. SPKR SETUP” from the MAIN MENU, select “AUTO SETUP” with the 3/4 cursor buttons, and press the OK/ENTER button to display the start screen.

4.Select the number of channels for the surround back speaker you are using.

For a 5.1 channel speaker system, select “NON” (Surround Back speaker off). (To use speaker C or multi speaker, select “NON”. See page 20, 37.)

Select “START” with the 3/4 cursor buttons and press the OK/ENTER button to start measurement.

AUTO SETUP

AUTO SETUP: START

MAIN ROOM

SURR BACK: 2CH

RETURNEXIT

5. Detection Check

During the detection check, the following OSD appears on the display and checks are made to detect dark sound in the listening room, whether there are speakers or not and polarity.

AUTO SETUP

SPEAKERS CHECK: --

NOW ANALYZING !!

CANCEL

EXIT

Note:				7.		Calibration Check
• The detection check measures the state of use of all						AUTO	SETUP
speakers whether actually used or not.
For example, if the center speaker is not used, the						SPEAKERS	CHECK:OK
test tone will require time to go from the L-channel						1ST MIC	POSITION!!
to the R-channel, therefore be careful not to unplug						START
the microphone or operate the SR7001 during this						CHECK
time.
6. When the detection check ends, the following							EXIT
OSD appears on the display.						Select “START” with the 3/4 cursor buttons
						and press the OK/ENTER button to measure
	AUTO		SETUP
	SPEAKERS			CHECK:OK		the first point (main listening position).
	1ST MIC		POSITION!!			During measurement, the following OSD
		START				appears on the display. At this point, you can
		CHECK
						cancel measurement by selecting “CANCEL”
						with the 3/4 cursor buttons and pressing the
					EXIT	OK/ENTER button.
						AUTO	SETUP
Here, to view the results of the detection check,
select “CHECK” with the 3/4 cursor buttons						NOW ANALYZING!!
and press the OK/ENTER button. The results
will be displayed.						CANCEL
	SPEAKER			CONFIG
	CHECK !!			SPEAKER
	FRONT		: YES				EXIT
	CENTER		: NON
	FRONT R		: YES
	SURR . R		: YES			When this measurement ends, the following
	SURR . B R : NON
						OSD appears on the display
	SURR . B L : NON
	SURR . L		: YES
	SUB W		: YES			AUTO	SETUP
	RETURN				EXIT	SPEAKERS	CHECK:OK
Ifthecheckresultsindicateanerror,takesuitable						2ND MIC	POSITION!!
						START
action with that item and remeasure. (For error						CALCULATE
messages, see “ERROR MESSAGES” on
page 30.)
After confirming the check results, select							EXIT
“RETURN” with the 3/4 cursor buttons and
press the OK/ENTER button to return to the
OSD menu.
At this point, you can select “EXIT” to end Auto
Setup and return to “2. SPKR SETUP”.

28