Mitsubishi 2033D Series UPS | Mitsubishi 2033D SERIES specs

MITSUBISHI	2033D SERIES UPS	Page Number:
ELECTRIC	OWNERS / TECHNICAL MANUAL	3-1

3.0INSTALLATION AND OPERATION

3.1Transportation and Installation

TABLE 3.1 How to transport and install the system

Transportation	Installation
Transport unit with forklift.	Using the pre drilled holes (4 - 24) in the
Carry with overhead crane using	UPS channel base, anchor the unit using
eyebolts provided.	appropriate hardware. (Not provided)

Note : Do not transport in a horizontal position. Cabinets must be maintained upright within +/- 15° of the vertical during handling.

3.2Installation Procedure

A)Note the load tolerance of the floor Refer to Table 3.2 for list of UPS weights.

TABLE 3.2 List of UPS weights

UPS Capacity (kVA)	30	50	80
Weight (lb)	2060	1810	1990

B)Minimum clearance required for ventilation

Right side	1.0" (25 mm) (not required when sidecars are used)
Left side	1.0"	(25 mm) (not required when sidecars are used)
Back side	0.0"	(0.0 mm)
Top side	23.6" (600 mm) (for air flow)

C)Space requirement for routine maintenance

Allow for the following space at the time of installation.

Front	39.4" (1000 mm)
Sides	0.0" (0.0 mm)
Rear	0.0" (0.0 mm)

MITSUBISHI ELECTRIC 2033D SERIES UPS

Image 33

Mitsubishi 2033D SERIES technical manual Mitsubishi 2033D Series UPS, Mitsubishi Electric 2033D Series UPS

Contents

ALN-H0963 Preface Table of Contents UPS Module Information List of Tables List of Figures How to use this Manual Introduction Important Safety Instructions Retain These Instructions Capacity kVA General Mitsubishi 2033D Series UPS Normal Operation Overview Internal Static Bypass Line Single Line Diagram Battery Operation Inverter supply at battery operation PCB External Contact Signal Terminal IOAU-05 Mitsubishi 2033D Series UPS Specifications Static Bypass Input AC Input Rating of Contactors and Fuses 540V 48A Operator Controls and Indicators EPO button Emergency Power Off button Battery operation Battery OP. yellowLED Display Load on inverter Load on Inverter green Load on bypass Load on Bypass green Liquid Crystal Display MenusStart/Stop screen Figure Measurement Menu Figure Start/Stop screen Setup Menu Figure 11 Main screen Input Power Failure 13 Main screen Fault indication Fault Indication Figure TN1 External Signal Terminal Block Remote EPO TN2 16 Control Wiring for External Contacts Output Contacts for external alarm annunciation Terminals 37 to 38, 39 to 40 Total Alarm contact OUT9 Terminals 33 to 34, 35 to 36 Minor Fault contact OUT8Input Contacts for remote access of UPS Terminals 3 to 4 Remote Inverter Stop input terminal IN2 Terminals 7 to 8 Power Demand Command contact input IN4 Terminals 5 to 6 Battery Temp. High contact input IN3Terminals 11 to 12 Asynchronous contact input IN6 Terminals 13 to 14 Charger IL. contact input IN7 Pin Not used External communication connector Mitsubishi Electric 2033D Series UPS Mitsubishi 2033D Series UPS Electric Owners / Technical Manual Battery Procedure for Cable Connections External Battery Supply Mitsubishi 2033D Series UPS Recommended cable size and torque requirements Crimp Type Compression Lug AUPS Terminal Designation 30kVA UPS BN,BP BN BP AC Bypass Input UPS-1 UPS-2 IOAU-05 TN2 IFAU-01Critical Load Cabinet Operating Procedures UPS Start-up Procedure UPS Shutdown ProcedureEPO Emergency Power Off Procedure Maintenance bypass set-up procedures Transfer of load from inverter to maintenance bypassTransfer of load from maintenance bypass to inverter Electric Owners / Technical Manual Response to UPS Failure UPS Fault UPS Component Parts Parts Replacement Contact Mitsubishi Electric Automation, Inc. at Fault Codes Mitsubishi Code List INV. or Conv Inverter Overload DC circuit failure Mitsubishi Electric Automation Inc 847