Specifications | Mitsubishi 2033D SERIES specification

MITSUBISHI	2033D SERIES UPS	Page Number:
ELECTRIC	OWNERS / TECHNICAL MANUAL	1-11

1.4Specifications

The UPS name plate displays the rated kVA as well as nominal voltages and currents. The name plate is located on the inside of the UPS front door.

TABLE 1.1 Power Specifications

	Rated output			Input voltage		Bypass input voltage			Output voltage
		Power		3 phase / 3 wire		3 phase / 3 wire			3 phase / 3 or 4 wire
	30kVA / 24kW			480V			480V		208V or 480V
	50kVA / 40kW			480V			480V		208V or 480V
	80kVA / 64kW			480V			480V		208V or 480V
	TABLE 1.2 UPS Module Information
	UPS	CABLE		WIDTH	DEPTH		HEIGHT		WEIGHT	HEATING
	[kVA]	ENTRY		[in / mm]	[in / mm]		[in / mm]		[lb./ kg]	[kBTU/h]

	30	BOTTOM		33.9 / 860	31.5 / 800		70.9 / 1800		2060 / 930	9.1
	50	BOTTOM		33.9 / 860	31.5 / 800		70.9 / 1800		1810 / 820	13.5
	80	BOTTOM		33.9 / 860	31.5 / 800		70.9 / 1800		1990 / 900	21.6

MITSUBISHI ELECTRIC 2033D SERIES UPS

Image 17

Mitsubishi 2033D SERIES technical manual Specifications

Contents

ALN-H0963 Preface Table of Contents UPS Module Information List of Tables List of Figures How to use this Manual Introduction Important Safety Instructions Retain These Instructions Capacity kVA General Mitsubishi 2033D Series UPS Normal Operation Overview Internal Static Bypass Line Single Line Diagram Battery Operation Inverter supply at battery operation PCB External Contact Signal Terminal IOAU-05 Mitsubishi 2033D Series UPS Specifications Static Bypass Input AC Input Rating of Contactors and Fuses 540V 48A Operator Controls and Indicators EPO button Emergency Power Off button Battery operation Battery OP. yellowLED Display Load on inverter Load on Inverter green Load on bypass Load on Bypass green Start/Stop screen Figure Liquid Crystal DisplayMenus Measurement Menu Figure Start/Stop screen Setup Menu Figure 11 Main screen Input Power Failure 13 Main screen Fault indication Fault Indication Figure TN1 External Signal Terminal Block Remote EPO TN2 16 Control Wiring for External Contacts Output Contacts for external alarm annunciation Terminals 37 to 38, 39 to 40 Total Alarm contact OUT9 Terminals 33 to 34, 35 to 36 Minor Fault contact OUT8Input Contacts for remote access of UPS Terminals 3 to 4 Remote Inverter Stop input terminal IN2 Terminals 7 to 8 Power Demand Command contact input IN4 Terminals 5 to 6 Battery Temp. High contact input IN3Terminals 11 to 12 Asynchronous contact input IN6 Terminals 13 to 14 Charger IL. contact input IN7 Pin Not used External communication connector Mitsubishi Electric 2033D Series UPS Mitsubishi 2033D Series UPS Electric Owners / Technical Manual Battery Procedure for Cable Connections External Battery Supply Mitsubishi 2033D Series UPS Recommended cable size and torque requirements Crimp Type Compression Lug AUPS Terminal Designation 30kVA UPS BN,BP BN BP AC Bypass Input Critical Load Cabinet UPS-1 UPS-2 IOAU-05 TN2IFAU-01 EPO Emergency Power Off Procedure Operating Procedures UPS Start-up ProcedureUPS Shutdown Procedure Transfer of load from maintenance bypass to inverter Maintenance bypass set-up proceduresTransfer of load from inverter to maintenance bypass Electric Owners / Technical Manual Response to UPS Failure UPS Fault UPS Component Parts Parts Replacement Contact Mitsubishi Electric Automation, Inc. at Fault Codes Mitsubishi Code List INV. or Conv Inverter Overload DC circuit failure Mitsubishi Electric Automation Inc 847