Narrow screen size 43 or Sxga | Mitsubishi Electronics PD-6130

Format Operation with Computer Signals

Switch to the wide screen mode to expand the 4 : 3 image to fill the entire screen.

1.Press the FORMAT button on the remote control.

2.Within 3 seconds ...

Press the FORMAT button again. The screen size switches as follows:

→ NARROW → STANDARD → EXPAND

NARROW screen size (4:3 or SXGA 5:4)

The picture has the same size as the normal computer image.

STANDARD screen size

The image is expanded in the horizontal direction.

EXPAND screen size

When wide signals are input.

STANDARD screen size

Information

Supported resolution

See page 40 for details on the display output of the various VESA signal standards supported by the monitor.

When 852 (848) dot 480 line wide VGA* signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are in- put

Select an appropriate setting for RGB SELECT mode referring to the“Table of Signals Supported” on page 40.

*“VGA”, “SVGA” and “SXGA” are registered trademarks of IBM, Inc. of the United States.

WARNING

DO NOT OPERATETHE PLASMA DISPLAY IN NARROW (4:3) SCREEN SIZE MODE FOR AN EXTENDED PERIOD. THIS CAN CAUSE PHOSPHOR BURN-IN.

14

Image 23

Mitsubishi Electronics PD-6130 Format Operation with Computer Signals, Narrow screen size 43 or Sxga, Expand screen size

Contents

Owner’s Guide Page Important Safety Instructions PD-5030/PD-6130 Risk of Electric Shock Do not Open PrecautionsImportant Information To avoid damage and prolong operating life Page Important No Abrasives Cleaning SafeguardsPlasma Display Screen & Cabinet Introduction to the PD-5030/ PD-6130 Plasma Monitors Features you’ll enjoy includeContents of the Package Introduction Contents Ventilation requirements for enclosure mounting How to Attach Options to the Plasma Monitor Front View Part Names and Function EXT Speaker L and R Rear View/ Terminal Board RGB/PC Remote Control 5AUTO Position Battery Installation and Replacement Approx 7m/23ft Using the wired remote control modeHandling the remote control Operating Range HD-5000 InstallationMitsubishi HD Receiver/Controller Connecting Your DVD Player Connecting Your VCR or Laser Disc Player External DVI Device with DVI-HDCP MonitorLink Pin Configuration DVI ConnectorMonitorLink Connections MonitorLink and MonitorLink Control Clamp Video signal RGB/DVD/HD signalLoop Out Cable Management To adjust the size or quality of the picture automatically To adjust the sound volumeTo cancel the sound To check the settings To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timer Format Sizes When viewing videos or digital video discs Expand screen size Format Operation with Computer Signals Supported resolution Narrow screen size 43 or Sxga Menu Operations On-Screen Menu OSM Controls Adjusting the picture Video Settings Menu Reducing noise in the picture Setting the color temperatureAdjusting the color to the desired level LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settings ColorView Audio Settings Menu Colorview settings Audio settings menu Example Setting Audio INPUT1 to Video Monitor Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture Adj Setting the on-screen menu Option1 Settings Menu BNC Input Settings Setting the BNC connectorsSetting a computer image to the correct RGB select screen Example Set the BNC Input mode to Comp RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settings Setting the power management for computer images Option2 Settings MenuResetting to the default values Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie Peak Bright settings Orbiter Function settings Orbiter settings Example Inverse SettingsSetting the time for INVERSE/WHITE Setting the time Soft Focus Setting the screen size for S1/S2 video inputSoft Focus settings Gray Level settings Black Level settings Setting the signal and black level for DVI signalS1/S2 settings PLUG/PLAY settings Present Time Option3 Settings MenuUsing the timer Present Time settings Special characters in the Program Timer screen Setting the power on mode Program Timer settings To reset the program IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings Button Lock settings To connect another display Loop Out setting Loop OUT settings To set the Loop OUT to on Setting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menus Communication Parameters RS-232C ControlApplication Connections Symptom Checks Remedy TroubleshootingPage Signals Specifications PD-5030 Specifications PD-6130 Computer input signals supported by this system Table of Signals SupportedSupported resolution Page Mitsubishi Plasma Display Panel Limited Warranty Declaration of Conformity