Description, Lamp Time LOW, Input | Mitsubishi Electronics XL7000U

Menu operation (continued)

INFORMATION menu

opt.

INFORMATION

	LAMP TIME (LOW)	****H
	SERIAL NUMBER	********...
	INPUT	COMPUTER1
	RESOLUTION	1024 x 768
	VERTICAL	60.00 Hz
	FREQUENCY	60.00 Hz
	HORIZONTAL	48.36 kHz
	FREQUENCY	48.36 kHz
R G	B	5WIRE
H V	SYNC. TYPE	5WIRE

ITEM	DESCRIPTION
LAMP TIME (LOW)	This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP is

LOW.

t 8IFOUIF-".1.0%&JT45"/%"3%UIJTJUFNTIPXTBMPOHFSMBNQPQFSBUJOHUJNFUIBO the actual time.

t 8IFOUIFMBNQPQFSBUJOHUJNFJTUPIPVSTi)wJTEJTQMBZFE5IFMBNQPQFSBUJOHUJNF exceeding 10 hours is indicated by the actual hours.

t 8IFOUIFMBNQPQFSBUJOHUJNFSFBDIFTIPVSTUIFCBSUVSOTUPZFMMPX8IFOJU reaches 3800 hours, the bar turns to red.

SERIAL NUMBER	The serial number of the projector is displayed.
INPUT	Indicates the name of the terminal to which the currently projected video signal is being input.
RESOLUTION	Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY	Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL FREQUENCY	Indicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE	Indicates the type of the sync signal for the currently projected video signal.

EN-38

Image 38

Mitsubishi Electronics XL7000U Description, Lamp Time LOW, Serial Number, Input, Resolution, Horizontal Frequency

Contents

XL7000 Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards Do not keep using the damaged projector Removing the batteries from the remote control Checking accessoriesInserting the batteries into the remote control Preparing your projector Control area Preparing your projectorOverview Bottom side IndicatorsRemote control Using the wired remote control Using the remote controlOperational range of the remote control Reception angle Setting by the remote control alone Using the remote controlSetting the ID number of the remote control Setting by using the projector Setting up the screen Setting up your projectorBefore setting up Screen size and projection distance Adjusting the position of the projected image Setting up your projectorSetup adjustment Changing the Auto Power OFF setting When ﬁne streaks are seen on projected images Setting High Altitude ModeSetting Image Reverse When the projected image is distorted Keystone → Reset → Keystone Adjustment using the Keystone modeAdjustment using the Cornerstone mode Keystone menu ARC menu Adjustment using the Curved modeLower RIGHT, Lower LEFT, Upper RIGHT, or Upper Left menu HORIZ. Origin or VERT. Origin menu Adjusting the origin to the vertical arc Be corrected by the CORNERSTONE-mode adjustment *OBEVTUZPSIVNJEQMBDF Front projection, ceiling mountingRear projection /FBSBIFBUFS Connecting the projector to a computer Viewing computer images About DDC Plugging the power cordViewing computer images For monitor connection Installing the terminal cover 3FNPWFUIFMFOTDBQ Conﬁrm the Power indicator lights up redProjecting images Select an input source $PWFSUIFMFOTXJUIUIFMFOTDBQUPQSPUFDUJUGSPNEVTU Direct Power OFFTo stop projecting Example of the setting procedure for external output When connecting to a notebook computerSetting of the resolution Blanking the screen temporarily Blank When a TV tuner or VCR is connected Connecting the projector to video equipmentConnecting to a video player, etc Viewing video images Viewing video images Projector + DVD player or Hdtv decoder Plugging in the power cord Connection for video equipment having a DVI-D terminal EN-27 Volume from the speaker Setting the aspect ratio How to change the settings With the remote control With the Feature menu See page 31 for menu setting Menu operation Image menu Installation menu Feature menuSignal menu Network menu Information menu Menu operation How to set the menusPress the  or  button to select an item to adjust Press the  or  button to select a menu to use Enhanced Image menuAuto See Auto Power on On / OFF Setting Function Lamp Mode StandardStandby Mode Standard Auto Power OFF High Altitude Mode Standard Menu Access Splash ID Screen Menu PositionCinema Mode Auto Aspect Normal Setup Auto Setting Function Advanced Menu EnterVideo Signal Auto / Ntsc / PAL / Secam Reset ALL Signal menu IP Config Enter Setting Function Projector NameNetwork Password Enter Default Gateway Lamp Time LOW ResolutionDescription Serial Number To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the tone of white Color Temp Color Enhancer Adjusting projected imagesAbout color temperature Select an item you want to set using  or  button Adjusting the ﬁneness of the image Super ResolutionAdjusting the tone of each color NCM Select NCM by pressing the  or  button How to adjust the computer image YES To adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive ﬁlter Network Password Settings Initial network settingsSetting Projector Name Enabling or disabling the network certiﬁcation Setting or Clearing Dhcp Initial network settingsIP Settings IP Address Settings Default Gateway Settings Setting the control systemSubnet Mask Settings Saving IP Config Settings Glossary Initialization of Network SettingsHow to Use Network Function Dhcp Changing the image displayed at the startup Advanced featuresSetting procedure To enable the password function Advanced featuresPassword function To cancel the password function Freeze Picture in Picture PinPMagnifying the displayed image Major functions PJLink supported commands Connection Interval of lamp replacement Replacing the lamp To replace the lamp Reset of the lamp operation timeReplacing the lamp When removing the lamp from the ceiling-mounted projector Cleaning of the lens MaintenanceCleaning of the projector and the ventilation slots Cleaning of the ﬁlter Mounting the lens option lens Replacing the lensRemoving the lens Troubleshooting No image appears on the screen Problem Solution Images are not displayed correctly TroubleshootingProblem Solution $IFDLUIBUUIFWPMVNFJTOUTFUUPMPX Images are not displayed correctly Problem SolutionOthers Problem Solution 3FTFUUIFMBNQPQFSBUJOHUJNF 4FFQBHF FOCUS/ZOOMJUUIFMBNQDPWFSTFDVSFMZ 4FFQBHF Power Status Filter Condition Possible Solution IndicatorsPower Status Filter Condition Replacement part option/not included in the box Speciﬁcations Speciﬁcations XGA85 Composite Sync ConnectorsDimension drawings unit mm Hdmi Serial With long throw zoom lens OL-XL7100LZ Speciﬁcation of the attached lensWith short throw zoom lens OL-XL7100SZ With tele throw zoom lens OL-XL7100TZ With rear projection short throw OL-XL7100FR Projection Mitsubishi Electric Corporation