Projection

Speciﬁcations (continued)

With rear projection short throw (OL-XL7100FR)

F No.			F2.2
Focal distance			f = 12.9 mm
Focus			Electrical drive
Picture size			40 inch (81 cm X 61 cm) - 200 inch (406 cm X 305 cm)

		Screen size					Projection		Lens shift height
Diagonal size		Width (W)			Height (H)		distance (L)		Standard (H0)
inch	cm	inch		cm	inch	cm	inch	m	inch	cm

40	102	32		81	24	61	24	0.6	-12	-30

60	152	48		122	36	91	37	0.9	-18	-46

80	203	64		163	48	122	50	1.3	-24	-61

100	254	80		203	60	152	63	1.6	-30	-76

120	305	96		244	72	183	76	1.9	-36	-91

150	381	120		305	90	229	95	2.4	-45	-114

200	508	160		406	120	305	127	3.2	-60	-152

The above ﬁgures are approximate and may be slightly different from the actual measurements.

t 1SPKFDUJPOOPUSFDPNNFOEFEJOTJ[FXJMMJODSFBTFEJTUPSUJPOBOESFEVDFUIFSFTPMVUJPO

t 5IFBEKVTUBCMFBOHMFJOUIFLFZTUPOFBEKVTUNFOUXJUIUIFMFOTEJGGFSTGSPNUIBUXJUIUIF9-6MFOT t *OUIFLFZTUPOFBEKVTUNFOUXJUIUIFMFOTUIFQSPQFSBTQFDUSBUJPNBZOPUCFPCUBJOFE

EN-67

Page 67

Image 67

Mitsubishi Electronics XL7000U user manual With rear projection short throw OL-XL7100FR, Projection

Contents

XL7000 Risk of Electric Shock Do not Open Contents Important safeguards Do not keep using the damaged projector Important safeguards Preparing your projector Checking accessoriesInserting the batteries into the remote control Removing the batteries from the remote control Overview Preparing your projectorControl area Remote control IndicatorsBottom side Reception angle Using the remote controlOperational range of the remote control Using the wired remote control Setting by using the projector Using the remote controlSetting the ID number of the remote control Setting by the remote control alone Screen size and projection distance Setting up your projectorBefore setting up Setting up the screen Changing the Auto Power OFF setting Setting up your projectorSetup adjustment Adjusting the position of the projected image When the projected image is distorted Setting High Altitude ModeSetting Image Reverse When ﬁne streaks are seen on projected images Keystone menu Adjustment using the Keystone modeAdjustment using the Cornerstone mode Keystone → Reset → Keystone HORIZ. Origin or VERT. Origin menu Adjustment using the Curved modeLower RIGHT, Lower LEFT, Upper RIGHT, or Upper Left menu ARC menu Be corrected by the CORNERSTONE-mode adjustment Adjusting the origin to the vertical arc /FBSBIFBUFS Front projection, ceiling mountingRear projection *OBEVTUZPSIVNJEQMBDF Viewing computer images Connecting the projector to a computer For monitor connection Plugging the power cordViewing computer images About DDC Installing the terminal cover Select an input source Conﬁrm the Power indicator lights up redProjecting images 3FNPWFUIFMFOTDBQ To stop projecting Direct Power OFF $PWFSUIFMFOTXJUIUIFMFOTDBQUPQSPUFDUJUGSPNEVTU Blanking the screen temporarily Blank When connecting to a notebook computerSetting of the resolution Example of the setting procedure for external output Viewing video images Connecting the projector to video equipmentConnecting to a video player, etc When a TV tuner or VCR is connected Projector + DVD player or Hdtv decoder Viewing video images Connection for video equipment having a DVI-D terminal Plugging in the power cord EN-27 Setting the aspect ratio Volume from the speaker With the Feature menu See page 31 for menu setting How to change the settings With the remote control Signal menu Network menu Information menu Image menu Installation menu Feature menuMenu operation Press the  or  button to select a menu to use How to set the menusPress the  or  button to select an item to adjust Menu operation See Image menuAuto Enhanced Auto Power OFF Setting Function Lamp Mode StandardStandby Mode Standard Auto Power on On / OFF Aspect Normal Menu Access Splash ID Screen Menu PositionCinema Mode Auto High Altitude Mode Standard Reset ALL Setting Function Advanced Menu EnterVideo Signal Auto / Ntsc / PAL / Secam Setup Auto Signal menu Default Gateway Setting Function Projector NameNetwork Password Enter IP Config Enter Serial Number ResolutionDescription Lamp Time LOW To adjust the tone of white Color Temp Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and Tint About color temperature Adjusting projected imagesColor Enhancer Select NCM by pressing the  or  button Adjusting the ﬁneness of the image Super ResolutionAdjusting the tone of each color NCM Select an item you want to set using  or  button YES How to adjust the computer image LPF Progressive ﬁlter Simple method to adjust the image positionTo adjust the horizontal position To adjust the vertical position Enabling or disabling the network certiﬁcation Initial network settingsSetting Projector Name Network Password Settings IP Address Settings Initial network settingsIP Settings Setting or Clearing Dhcp Saving IP Config Settings Setting the control systemSubnet Mask Settings Default Gateway Settings Dhcp Initialization of Network SettingsHow to Use Network Function Glossary Setting procedure Advanced featuresChanging the image displayed at the startup To cancel the password function Advanced featuresPassword function To enable the password function Magnifying the displayed image Picture in Picture PinPFreeze Major functions Connection PJLink supported commands Replacing the lamp Interval of lamp replacement Replacing the lamp Reset of the lamp operation timeTo replace the lamp When removing the lamp from the ceiling-mounted projector Cleaning of the ﬁlter MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lens Removing the lens Replacing the lensMounting the lens option lens No image appears on the screen Problem Solution Troubleshooting Problem Solution TroubleshootingImages are not displayed correctly Others Problem Solution Images are not displayed correctly Problem Solution$IFDLUIBUUIFWPMVNFJTOUTFUUPMPX JUUIFMBNQDPWFSTFDVSFMZ 4FFQBHF FOCUS/ZOOM3FTFUUIFMBNQPQFSBUJOHUJNF 4FFQBHF Power Status Filter Condition IndicatorsPower Status Filter Condition Possible Solution Speciﬁcations Replacement part option/not included in the box XGA85 Speciﬁcations Hdmi Serial ConnectorsDimension drawings unit mm Composite Sync With tele throw zoom lens OL-XL7100TZ Speciﬁcation of the attached lensWith short throw zoom lens OL-XL7100SZ With long throw zoom lens OL-XL7100LZ Projection With rear projection short throw OL-XL7100FR Mitsubishi Electric Corporation

Mitsubishi Electronics XL7000U With rear projection short throw OL-XL7100FR, Projection

Models: XL7000U

Speciﬁcations (continued)

With rear projection short throw (OL-XL7100FR)

distance (L)