Setting up your projector (continued)

Setting HIGH ALTITUDE MODE

t 4FU)*()"-5*56%&.0%&JOUIF'&"563&NFOV according to the altitude at which you use the projector. The default setting is STANDARD.

t 4FMFDU45"/%"3%XIFOVTJOHUIFQSPKFDUPSBUBO altitude from 0 to 1500 meters.

t 4FMFDU)*()"-5*56%&XIFOVTJOHUIFQSPKFDUPSBU an altitude from 1500 to 2700 meters.

Important:

t *GZPVTFMFDU45"/%"3%XIFOVTJOHUIFQSPKFDUPS at an altitude higher than 1500 meters, the projector may break down or fail.

t 8IFOZPVVTFUIFQSPKFDUPSJOUIF)*()"-5*56%& mode, only floor installation and ceiling installation are allowed.

t 8IFOZPVTFMFDU)*()"-5*56%&JO)*()

ALTITUDE MODE, LAMP MODE setting automatically changes to LOW.

(See page 31 for menu setting.)

1.Display the FEATURE menu.

2.Select HIGH ALTITUDE MODE by pressing the or button.

HIGH ALTITUDE MODE

STANDARD

 

 

 

 

 

 

 

3. Press the ENTER button.

HIGH ALTITUDE MODE

HIGH ALTITUDE MODE

STANDARD

4.Select STANDARD or HIGH ALTITUDE by pressing the or button.

5.Press the ENTER button.

Setting IMAGE REVERSE

Set IMAGE REVERSE in the INSTALLATION menu according to the orientation of the projector. The default setting is OFF.

t 4FMFDU0''GPSUIFDPNCJOBUJPOPGnPPSJOTUBMMBUJPO and front projection.

t 4FMFDU.*3303*/7&35GPSUIFDPNCJOBUJPOPG ceiling installation and front projection.

t 4FMFDU.*3303GPSUIFDPNCJOBUJPOPGnPPS installation and rear projection.

t 4FMFDU*/7&35GPSUIFDPNCJOBUJPOPGDFJMJOH installation and rear projection.

(See page 31 for menu setting.)

1.Display the INSTALLATION menu.

2.Select IMAGE REVERSE by pressing the or button.

Correcting skewed or distorted image

For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.

Screen

Adjustment feet

1.Tilt up the projector to the appropriate angle.

2.Rotate the adjustment feet for fine adjustment.

Important:

t %POUUSBOTQPSUUIFQSPKFDUPSXJUIJUTBEKVTUNFOU feet extended. Otherwise the adjustment feet may be damaged.

When fine streaks are seen on projected images

This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a little. (See page 12 for focus adjustment.)

When the projected image is distorted:

When the projected image is distorted, carry out any of the KEYSTONE, CORNERSTONE, and CURVED- mode adjustments to correct the distortion.

When the image distorts in a trapezoid shape, use the KEYSTONE-mode adjustment. For fine adjustment of the image shape, use the CORNERSTONE-mode adjustment. To adjust the image projected on a curved surface, use the CURVED-mode adjustment.

When you press the ENTER/GEOMETRY button on the projector or the GEOMETRY button on the remote control, the menu switches in the order of KEYSTONE, CORNERSTONE, CURVED, regular display, KEYSTONE...

IMAGE REVERSE

OFF

3.Select OFF, MIRROR, INVERT or MIRROR INVERT by pressing the or button.

EN-13

Page 13
Image 13
Mitsubishi Electronics XL7000U Setting High Altitude Mode, Setting Image Reverse, Correcting skewed or distorted image