MTD PS manual

A. GRIP SAW FIRMLY: Hold the chain saw firmly with

both hands when the motor is running. Keep a good firm grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle.

B. Do not over reach.

C. Keep proper footing and balance at all times.

D. Do not let the nose of the guide bar contact a log, branch, ground or other obstruction.

E. Do not cut above shoulder height.

F.Use devices, such as low-kickback chain, guide bar nose guards, chain brakes and special guide bars, which reduce the risks associated with kickback.

G.Use only replacement bars and chains specified by the manufacturer or the equivalent.

H.There are no other replacement components for achieving kickback protection in accordance with CSA Z62.3.

20.POWER SUPPLY: Connect the chain saw to correct voltage; be sure that the voltage supplied is the same as that specified on the nameplate of the tool.

21.DO NOT operate a chain saw that is damaged, improperly adjusted, or not completely and securely assembled. Be sure that the saw chain stops moving when the trigger is released.

22.DO NOT attempt operations beyond your capacity or experience.

23.DO NOT operate a chain saw with one hand! Serious injury to the operator, helpers, or bystanders may result from one-handed operation. A chain saw is intended for two-handed use.

24.TO REDUCE potential for electric shock, do not oper- ate the saw on wet or slippery surfaces, or during snow storms, rain storms, and other adverse weather conditions.

25.DO NOT allow dirt, debris or sawdust to build up on the motor or outside air vents.

26.Follow the manufacturer’s sharpening and mainte- nance instructions for the saw chain.

27.Cut at high motor speeds.

28.Operation of a chain saw should be restricted to mature, properly instructed individuals.

29.Your chain saw is intended for occasional homeowner use. It is not made for heavy continuous use.

30.DO NOT FORCE a small saw to do a job requiring a heavier duty unit.

31.EXAMINE THE ELECTRICAL SWITCHES. Do not use the chain saw if the switches do not properly turn on and off. Do not attempt to make any repairs to the electric switches. Take your saw to a MTD Authorized Service Center.

32.MAINTAIN EXTENSION CORDS. Inspect the exten- sion cords periodically and replace if damaged. Only use power cords that are suitably marked for outdoor use.

33.DO NOT OPERATE YOUR CHAIN SAW near or around flammable liquids or gases, whether in or out of doors. An explosion and/or fire may result.

34.This electric powered saw is classified by CSA as a Class 2C saw. It is intended for infrequent use by homeowner’s, cottagers and campers, and for such general applications such as clearing, pruning, cutting firewood, etc. It is not intended for prolonged use. If the intended use involves prolonged periods of opera- tion, this may cause circulatory problems in the user’s hands due to vibration. It may be appropriate to use a saw having an anti-vibration feature.

35.NEVER REMOVE, modify or make inoperative any safety device furnished with your unit.

36.Safety clothing required by your safety organizations, government regulations, or your employer should be used; otherwise, snug fitting clothing, safety footwear, and hand and ear protection should be worn.

37.When felling, keep at least 2 tree lengths between yourself and your fellow workers.

38.All chain saw service, other than the items listed in the user manual safety and maintenance instructions, should be performed by competent chain saw person- nel. Do not attempt to repair it yourself; there are no user serviceable parts inside.

NOTE: Low-kickback saw chain is chain that has met the kickback performance requirements of ANSI B175.1-1991 and is in accordance with CSA Z62.3. Do not use other replacement chain unless it has met these requirements for your specific model.

39.DO NOT USE ANY OTHER CUTTING ATTACH- MENT OR ACCESSORIES. Use only MTD

replacement parts and accessories, which are designed specifically to enhance the performance and maximize the safe operation of our products. Failure to do so may cause poor performance and possible injury. Use only the chain and bar supplied with this product. Do not use any other cutting attachment. Use of such attachments will void your factory warranty and could result in serious bodily injury.

8