Result Codes | Multi-Tech Systems BL-Series specification

Chapter 5 - Command Mode

5.3Result Codes

The Command mode provides you with several responses, or “Result Codes”, that can aid you in Command mode operation. These Result Codes are displayed on your video monitor.

You can choose result codes that closely match those of the standard AT command set, or choose enhanced function result codes that have been used in Multi-Tech modems ("Multi-Tech"responses). The &Q command selects which result codes will be used.

You can choose to have these Result Codes displayed in either “verbose” (full words) or “terse” (digits) format. This is controlled by the ATV0 (terse) or ATV1 (verbose) commands. The modem defaults to verbose format.

AT&Q0 selects Multi-Tech responses with Reliable/LAPM/Compression modifiers. The terse response code for CONNECT 2400 is 9. AT&Q1 selects Standard AT command set responses. The terse result code for CONNECT 2400 is 10.

The following tables define the result codes generated by the &Q command (refer to Appendix G for Result Code Summary).

"Multi-Tech" Result Codes

2834 Series
TERSE	VERBOSE	TERSE	VERBOSE
0	OK	11*	CONNECT 4800
1	CONNECT	12*	CONNECT 9600
2	RING	13*	CONNECT 14400
3	NO CARRIER	19*	CONNECT 19200
4	ERROR	21*	CONNECT 21600
5*	CONNECT 1200	24*	CONNECT 24000
6	NO DIALTONE	26*	CONNECT 26400
7	BUSY	28*	CONNECT 28800
8	NO ANSWER	31*	CONNECT 31200
9*	CONNECT 2400	33*	CONNECT 33600
1932 Series
TERSE	VERBOSE	TERSE	VERBOSE
0	OK	8	NO ANSWER
1	CONNECT	9*	CONNECT 2400
2	RING	11*	CONNECT 4800
3	NO CARRIER	12*	CONNECT 9600
4	ERROR	13*	CONNECT 14400
5*	CONNECT 1200	19*	CONNECT 19200
7	BUSY
1432 Series
TERSE	VERBOSE	TERSE	VERBOSE
0	OK	7	BUSY
1	CONNECT	8	NO ANSWER
2	RING	9*	CONNECT 2400
3	NO CARRIER	11*	CONNECT 4800
4	ERROR	12*	CONNECT 9600
5*	CONNECT 1200	13*	CONNECT 14400

*With MNP error correction on, RELIABLE (or R) is added to these result codes. With LAP-M error correction on, LAP-M (or L) is added to these result codes. With data compression on, COMPRESSED (or C) is added. (Note these "Extended" Result Codes are displayed when your modem is set up to do so with an X1, X2, X3, or X4 command.)

47

Image 47

Multi-Tech Systems BL-Series manual Multi-Tech Result Codes Series

Contents

User Guide Record of Revisions User Guide Contents Registers Command ModeCallback Security and Remote Configuration Manual Dial and Automatic Answer Appendixes Modem TestingDIP-Switch Settings Warranty, Service and Tech SupportPage Introduction and Description Introduction How To Use This Manual DIP-Switches AT Command Mode OperationCallback and Remote Configuration Testing Your Modem 2 1932 Series Features Modem Features1 2834 Series Features Fax Features 3 1432 Series Features Technical Specifications Introduction and Description Mode of OperationIntelligent Features Command Buffer Carrier Frequencies 300 bps Bell Standard Fax Carrier FrequenciesLease Line Restoral Carrier Frequencies Operating Temperature ConnectorsDiagnostics Indicators Models Only PowerModem LED Indicators Controls on PC Board MultiModemBL User Guide Installation and Connection Unpacking MT2834BL shown What is in Your Modem Package? Installation Procedure InstallationSafety Warnings MultiModemBL/BLI Connections MultiModemBLK Connections Cabling Procedure MT1432BLK and MT2834BLK Loading Trio DataFAX Software Installation and Connection Is Your Modem Ready for Use? Software Configuration and Modem Basics How Can You Identify Your Uart Type? Serial Port Limitations 16550 Uart and Windows Configuring Your SoftwareConfiguring Software for Your Modem Software Configuration Other Parameters Changing Default ParametersPC Initialization Strings Terminal Emulation Configuring Software for Your ComputerConfiguring Software for the Remote System Macintosh Initialization AT &F S0=0 X4 &E14 M When to Disable Data CompressionDisabling Error Correction File Transfer Protocols Simple Operations Answer/Originate Voice/Data Toggle SwitchModem Basics MultiModemBL User Guide Manual Dial and Automatic Answer Dialing/On-Line/Answering Manual Dial and Automatic Answer Manual Dial Backup Call TerminationDial Backup and Leased Line Restoral Automatic Leased Line Restoral Operation Manual Call Origination Dial-Up Operation Manual Answering Automatic Answering Call Termination Abort TimerHandshaking Details Command Mode AT Command Editing Functional Modes Command Mode Summary of AT Commands Flow Control Disabled Normal ModeAuto-Reliable Mode Reliable Mode Callback Security Enable/Disable Enable/Disable Reading Line Probe From DSP during handshakeDisplay of Signal Strength Information Passwords for Callback Phone Numbers Multi-Tech Result Codes Series Result Codes MultiModemBL User Guide Standard AT Result Codes Series Dialing a Stored Number N Dialing Commands Dialing Action CommandsDial Command D Continuous Redial not used in BLI/BLK a or Set Pulse Dial Ratios &P Not used in BLK Dial Modifier CommandsVoice/Data Dialing $VD Pulse or Tone Dial P T Long Space Disconnect Y Return to Command Mode After Dial Command ExecutionReverse the Mode of Operation R Automatic Pauses in Dialing Quiet Answer @ Calling Card Detect Tones $ Listing Numbers Stored in Memory L Phone Number Memory CommandsStoring Phone Numbers D...N Number Linking NN Modem Reset Z Configuration and Default Storage CommandsLoading Factory Defaults &F Synchronous Transmit Clock Select &X Async/Sync Mode Switching &MUnix Uucp Spoofing $SP Result Codes Multi-Tech or Standard AT &Q Command Response Result Code CommandsEcho Command Mode Characters E Result Codes Enable/Disable and No Response Answer Q Result Codes Basic and Extended and Call Progress Selection Bell/V.21 Tone Not Used in BLK Models B Phone Line Conditioning CommandsEnable/Disable Trelis Coded Modulation #T Guard Tones Not Used in BLI or BLK Models &G Cleardown at Disconnect &CD 2834 Series only Fallback Modes When On-Line #FEnable/Disable Lowspeed Fast Connect $FC 2834 Series only Auto Speed Detect #A CTS Control &R 7 RS-232C Interface Control CommandsCarrier Detect Control &C Data Terminal Ready Control &D DSR/CD Interaction Control &SF Data Set Ready Control &SCTS/RTS Interaction Control &RF Reliable Mode &E2 Error Correction CommandsNormal Mode &E0 Auto-Reliable Mode &E1 Auto-Reliable Buffering $A Mode Select #LOriginate Mode Answer Mode Retransmit Count $R Enable/Disable Auto Reliable Fallback Character $FError Correction/300bps $E Modem-Initiated Flow Control Flow Control CommandsHardware Flow Control &E4 Xon/Xoff Flow Control &E5 Hewlett-Packard ENQ/ACK Pacing &E9 Xon/Xoff Pass-Through &E7Send Xon/Xoff Characters #X Parity Selection #P Normal Mode Modem Flow Control On &E11Terminal/Computer Initiated Pacing &E13 Maximum Block Size &BS Enq/Ack Pacing Commands Normal/Auto-Reliable/Reliable Mode CommandsXon/Xoff Pass-Through Commands Modem Baud Rate $MB Speed Conversion CommandsSpeed Conversion $BA Command Mode Series Serial Port Baud Rate $SB Immediate Action Commands Off Hook H Listing On-Line Diagnostics L8 Exiting Command Mode, Going Back On-Line O Line Probe Commands 2834 Series onlyForce Answer Mode a MultiModemBL User Guide Registers Return Character Number of Rings Until Modem AnswersRings Which Have Occurred Escape Code Character Wait Time for Dial Tone Time for Carrier Abort TimerLine Feed Character Backspace Character S11 Tone Dialing Tone Spacing and Duration S10 Carrier Loss Disconnect Delay TimeS13 Remote Configuration Escape Character Carrier Detect Response Time S17 Changing Break Time S15 Callback Time DelayS19 Dial-Back Timer S16 Callback Attempts S25 DTR Dropout Time S26 Failed Password AttemptsS29 Local Inactivity Timer S24 PBX/CBX Disconnect Drop Time for DSR/CTS/CD S37 Time Between DTR Active and Modem On-Hook S30 Inactivity TimerS32 Time Elapse for Escape Sequence S36 Time Between DTR Inactive and Modem Off-Hook S48 Program V.34bis Connect Speeds 2834 Series only Examples of Reading Values Reading and Assigning S-Register ValuesExamples of Assigning Values AT Command and S-Register Summary Callback Security and Remote Configuration Callback Feature Description To change your Remote Configuration feature status Remote Configuration DescriptionCallback Security and Remote Configuration AT#CBN1xxxxxxxxxxCR To set parity of the password/message promptAT#CBN0xxxxxxxxxxCR Callback Operational Sequence Procedures Remote Configuration Operation Procedures StepProcedure Remote Configuration Procedures Change Login Password Remote Configuration and Callback Security AT CommandsAssign Passwords for Callback Phone Numbers #CBN Callback Security Enable/Disable Erase Callback Phone Number #RDNxx Erase Callback Password Remote Configuration/Callback Security S-Registers MultiModemBL User Guide Modem Testing Introduction Local Analog Loopback Test/V.54 Loop Modem Testing 100 Digital Loopback Test/V.54 Loop 2 Local/Manual 101 Digital Loopback Test/V.54 Loop 2 Remote/Automatic 4A. Back-to-Back Test Cabling Back-to-Back Test Local Analog Loopback Test Synchronous Mode Synchronous Mode Testing Synchronous Mode Digital Loopback Test local/manual 104 Digital Loopback Test Local/Manual Synchronous Mode Synchronous Mode Digital Loopback Test remote/automatic 105 Digital Loopback Test Remote/Automatic Synchronous Mode MultiModemBL User Guide 106 DIP-Switch Settings PC Board BL models 108 109 DIP-Switch Option SettingsDIP-Switch Settings 110 Switch #4 AS/400 Mode Synchronous Mode/Leased Line/Dial-UP1432 Series 111 112 113 114 Speaker Volume ControlMultiModemBL User Guide Series 115 Recording Option ConfigurationsSwitch Function Position Effect 116 DIP Switches #13-14DIP Switches #15-16 Warranty, Service and Tech Support 118 Limited WarrantyOn-line Warranty Registration Recording Modem Information ServiceWarranty, Service and Tech Support Tech Support To Download a file Multi-Tech BBSTo log on to the Multi-Tech BBS About Multi-Tech’s Internet Presence Using FlashPro to Upgrade Modem FirmwareAbout the Multi-Tech Fax-Back Service Upgrading the MultiModem 122 About Ordering AccessoriesSupplyNet Online Ordering Instructions Appendixes 124 Appendix a TroubleshootingNone of the LEDs Light When the Modem Is On Modem Does Not Respond to Commands 125 Appendix a Troubleshooting 126 Modem Dials But Cannot Make a Connection 127 Modem Cannot Connect When AnsweringModem Disconnects While On-line File Transfer Is Slower Than It Should Be 128 Am Losing DataAm Getting Garbage Characters on the Monitor 129 Appendix B Ascii Conversion Chart 130 Appendix C Dial Pulse and Tone-Dial FrequenciesDial Pulses Tone Dial Frequencies #An Appendix D AT Command SummaryCommand Values Description $An SN d BS n$BA n CD n $Fn $EBn#Fn $FCn $MBn $HnL10 #Ln Sr=n NdNe$Rn RFn #Tn $SBnSFn $SPn 137 #Xn+++ATCR Callback Security/Remote Configuration Command Summary 25bis Commands Password Command Summary 140 Appendix E DIP-Switch SummaryAsynchronous Mode 141 Synchronous ModeAppendix E DIP-Switch Summary 142 Appendix F S-Register Summary S29 S24S25 S26 145 Appendix G Result Code SummaryAppendix G Result Code Summary Terse Digit Verbose Words Effect 146 Appendix H V.25bis Operation Delayed and Forbidden NumbersAppendix H V.25bis Operation 25bis Operation 148 25bis DIP-Switches25bis Set-Up and Initialization 149 25bis Mode AT Commands25bis Responses Result Codes Dial Phone Number Provided CRN Command 25bis AT CommandsEnable/Disable V.25bis Mode $V Command Change Serial Baud Rate CSP Command DTR Dialing $D Command Listing Delayed Phone Numbers RLD CommandListing Forbidden Phone Number RLF Command Disregard or Connect to Incoming Calls DIC or CIC Command Austria ITU V.25bis Country Specific InformationItaly Switzerland 153 Appendix H V.25bis Operation FranceBelgium Singapore Figure I-1. RS232 Cable IBM PC Appendix I MultiModemBL Cables Figure I-4. MAC Cable 155 Appendix J RS-232C Interface Specifications 156 Appendix J RS-232C Interface SpecificationsSignal Function Assignment Circuit Source Pin Designation Eia Clear To Send Pin 5, CTS CB Signal Ground Pin 7, SG ABReceived Data Pin 3, RD BB Request To Send Pin 4, RTS CA Receive Clock Pin 17, RC DD Ring Indicator Pin 22, RI CETest Voltage Pin 9 Transmit Clock Pin 15, TC DB 159 Terminal Busy Out of Service Pin 25, OOSExternal Transmit Clock Pin 24, XTC 160 Appendix K Regulatory Information EMC, Safety and Terminal Directive ComplianceCompliance with European Community Requirements European Directives User Guide Statement 162 International Modem RestrictionsNew Zealand Telecom Warning Notice 163 FCC Regulations for Telephone Line Interconnection Industry Canada Canadian Limitations NoticeClass a Statement FCC Part 165 Index 166 Functional Description of RS232C SIG 167 XON/XOFF 168