Manuals / Multi-Tech Systems / Computer Equipment / All in One Printer

Multi-Tech Systems MT5600BA, MT5600BL manual Download the Upgrade File, Extract the Upgrade Files

Models: MT5600BA MT5600BL

1 118

Download 118 pages 61.79 Kb

Page 110

MultiModemII User Guide

Step 3: Download the Upgrade File

Multi-Tech Web Site

1.If you are not already at the Firmware page of the Multi-Tech Web site, follow the procedure in “Step 2: Identify the Current Firmware.”

2.Click on the upgrade file name for your modem, and save the file to a temporary location on your hard disk.

Multi-Tech BBS

1.If you have not already found the upgrade file for your modem on the Multi- Tech BBS, follow the procedure in “Step 2: Identify the Current Firmware.”

2.Type the number of the upgrade file for your modem, and then press ENTER.

3.Type D and press ENTER to list the file to be downloaded.

4.If the correct file is listed, press ENTER; otherwise use the Q command to return to the previous menu.

5.Type Z and press ENTER to select the Zmodem transfer protocol.

6.The download begins automatically. As the file is copied to your hard disk, a dialog box reports on the progress of the download.

7.To log off the BBS, press ENTER, type G for “good-bye,” and then press ENTER twice more.

Step 4: Extract the Upgrade Files

1.Move the downloaded upgrade file to a temporary directory or folder on your hard disk.

2.The file is a self-extracting archive. Extract the files by typing the upgrade file name in DOS or double-clicking it in Windows.

Step 5: Set the Modem to the Factory Defaults

Before you flash your modem, it is important that you issue the AT&F command to set it to the factory default parameters. You should also record the parameters that are currently stored in your modem so you can reprogram it after flashing.

1.Run your favorite terminal program. If you are using Windows 95 or Windows NT, you can use HyperTerminal. If you are using Windows 3.11, you can use Windows Terminal.

2.In the program’s terminal window, type AT&V and press ENTER to list your modem’s current parameters.

3.Record your parameters by saving the screens and sending them to your printer.

4.Type AT&F and press ENTER to reset your modem to the factory defaults.

5.Close the terminal program.

102

Image 110

Multi-Tech Systems MT5600BA Download the Upgrade File, Extract the Upgrade Files, Set the Modem to the Factory Defaults

Contents

Model MT5600BA Model MT5600BL Record of Revisions FCC Part Quick Start Using the Front PanelIntroduction MultiModemII User Guide Solving Problems AT Commands, S-Registers & Result CodesRemote Configuration Callback Security Appendix C Loopback Tests Appendix D Warranty, Service, and Technical SupportAppendix a Regulatory Compliance Appendix E Upgrading the Modem Contents Viii Introduction Product Description FeaturesIntroduction Introduction Data What Is in Your Modem Package? Related Manuals Quick Start We supply Safety WarningsWhat You Will Need You supply Dialup Connection Connect the Modem to Your SystemRS232 Connection Quick Start Power Connection Two-Wire Leased Line ConnectionFour-Wire Leased Line Connection Power-On Test Removing Your Old Modem from Windows Install the Modem in WindowsAdding the Modem to Windows Install and Configure Your Software Call the Multi-Tech BBS Trio DataComm Windows HyperTerminal Windows Terminal Microsoft Fax Send a FaxTrio Fax Select Start Programs Accessories Fax Compose new fax References MultiModemII User Guide Using the Front Panel Modem Configuration LED Indicators Option Selection Using the Front PanelLiquid Crystal Display LCD Menu Structure MultiModemII User Guide Menu Overview Using the Front Panel Status Trunk MultiModemII User Guide Basic Options Trunk Using the Front Panel Advanced Options Trunk MultiModemII User Guide Remote Configuration Options Trunk Diagnostic Options Trunk Using the Front Panel Phone Number Memory Options Trunk Caller ID Options Trunk Menu Options Status Using the Front Panel Basic Options Advanced Options Implemented Remote Configuration Options Caller ID Options MultiModemII User Guide Diagnostic OptionsPhone Number Memory Options AT Commands Registers Result Codes Introduction AT Commands AT Commands, S-Registers, and Result Codes Hook Control Echo Command Mode CharactersDS= y Dial Stored Telephone Number Information Request Return Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Result Codes Enable/Disable Read Register Value Select RegisterSet Register Value Tone Dialing Long Space Disconnect Modem ResetResult Code Selection Data Carrier Detect DCD Control Data Terminal Ready DTR Control Error Correction ModesLoad Factory Settings Modem-Initiated Flow Control Flow Control Selection Communications Mode22bis Guard Tone Control Clear to Send CTS Control Sync/Async ModeTest Commands Data Set Ready DSR Control Display Last Connection Statistics Display Current ConfigurationStore Current Configuration Synchronous Clock Source Zy =x Store Telephone Number Select Profile for Hard ResetLine Signal Level Data Compression Control \An Maximum MNP Block Size Line Signal QualityPCM Code Selection \Bn Transmit Break \Nn Error Correction Mode Selection \Vn Single Line Connect Message +MS= Modulation Selection Reserved,maxTXrateCR MNP Extended Services Command #CBPy=x Store Callback Password Command -SDR=nDistinctive Ring ControlCommand #CBNy=x Store Callback Number Flash Memory Download Command $SBn Serial Port Baud Rate Command #CID= n Caller IDCallback Enable/Disable Escape Sequence Register Unit Range Default Description Registers S32 S36 S46 Result Codes Terse Verbose Description Protocol ALT +FCERROR MultiModemII User Guide Remote Configuration Changing the Remote Configuration Password Basic ProcedureSetup Remote Configuration Changing the Remote Escape Character MultiModemII User Guide Callback Security Setup Procedures Turning Callback Security On and Off Assigning Callback Passwords Callback Security Assigning Callback Phone Numbers Command #CBN y= x Store Callback Number Calling ProcedureCallback Security Commands Command #CBPy=x Store Callback Password Callback Assignments MultiModemII User Guide Leased Line Operation Two-Wire Setup Four-Wire Setup Leased Line Operation Dial Backup and Leased Line Restoral Dial Backup and Leased Line Restoral Setup Leased Line Operation MultiModemII User Guide Solving Problems None of the Indicators Light Modem Does Not Respond to Commands Solving Problems Modem Dials But Cannot Connect Modem4Disconnects While Online Modem4Cannot Connect When Answering File Transfer4Is Slower Than It Should Be Modem4Doesn’t Work with Caller ID Data Is Being LostThere Are Garbage4 Characters on the Monitor Fax and Data4Software Can’t Run at the Same Time Appendixes Appendix a Regulatory Compliance FCC Part 68 Telecom Fax Branding Statement Regulatory Compliance Commission Decision CTR21 Canadian Limitations NoticeInternational Modem Restrictions EMC, Safety, and Terminal Directive Compliance New Zealand Telecom Warning Notice Appendix B Technical Specifications Technical Specifications Receiver Sensitivity Loopback Tests Test procedureLocal Analog Loopback Test V.54 Loop Remote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback test Local Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback test Back-to-Back Test Figure C-5. Back-to-back test connections Limited Warranty Service Technical Support Online Warranty RegistrationWarranty, Service, and Technical Support Multi-Tech BBS About the Internet Ordering Modem Accessories SupplyNet Online Ordering Instructions Upgrade Overview Identify the Modem Firmware Multi-Tech BBS Identify the Current Firmware VersionMulti-Tech Web Site Upgrading the Modem Set the Modem to the Factory Defaults Download the Upgrade FileExtract the Upgrade Files Upgrade the Modem’s Firmware Restore Your Parameters Appendix F Cable Pinouts RS-232 Pinouts Leased Line Pinouts Cable Pinouts Appendix G Ascii Character Map Ctrl Code Hex Dec Index 108 Index 110