Leased Line Pinouts, Cable Pinouts | Multi-Tech Systems MT5600BL

F Cable Pinouts

DTE Mini-DIN

8-pin connector

				SG, RxD+
TxD-	6	7	8	RxD-
TxD-	3	4	5
	3	4	5
		1	2

HSKi (CTS)

HSKo (RTS)

Figure F-3. Macintosh cable.

DCE DB-25 connector

2 TD

3 RD

4 RTS

5 CTS

6 DSR

7 GND

8 CD

20 DTR

22 RI

Leased Line Pinouts

	2 3 4 5
	2	Red (Tip)
	3
	4	Green (Ring)
	5	Green (Ring)
	5

RJ-11

Modular Plug

Figure F-4. Two-wire leased line cable.

To Terminal Block Screws

	2 3 4 5
	3	Red
	3	Transmit Pair
	4	Transmit Pair
	4	Green
		Green
		Yellow

	2	Receive Pair
	5
		Black

RJ-11

Modular Plug

Figure F-5. Four-wire leased line cable.

To Terminal Block Screws

105

Image 113

Multi-Tech Systems MT5600BL, MT5600BA manual Leased Line Pinouts, Cable Pinouts

Contents

Model MT5600BA Model MT5600BL Record of Revisions FCC Part Introduction Using the Front PanelQuick Start MultiModemII User Guide Remote Configuration AT Commands, S-Registers & Result CodesSolving Problems Callback Security Appendix a Regulatory Compliance Appendix D Warranty, Service, and Technical SupportAppendix C Loopback Tests Appendix E Upgrading the Modem Contents Viii Introduction Product Description FeaturesIntroduction Data Introduction Related Manuals What Is in Your Modem Package? Quick Start What You Will Need Safety WarningsWe supply You supply RS232 Connection Connect the Modem to Your SystemDialup Connection Quick Start Four-Wire Leased Line Connection Two-Wire Leased Line ConnectionPower Connection Power-On Test Removing Your Old Modem from Windows Install the Modem in WindowsAdding the Modem to Windows Install and Configure Your Software Trio DataComm Call the Multi-Tech BBS Windows HyperTerminal Windows Terminal Microsoft Fax Send a FaxTrio Fax References Select Start Programs Accessories Fax Compose new fax MultiModemII User Guide Using the Front Panel LED Indicators Modem Configuration Liquid Crystal Display LCD Using the Front PanelOption Selection Menu Structure MultiModemII User Guide Menu Overview Using the Front Panel Status Trunk MultiModemII User Guide Basic Options Trunk Using the Front Panel Advanced Options Trunk Diagnostic Options Trunk MultiModemII User Guide Remote Configuration Options Trunk Caller ID Options Trunk Using the Front Panel Phone Number Memory Options Trunk Status Menu Options Using the Front Panel Basic Options Implemented Advanced Options Remote Configuration Options Caller ID Options MultiModemII User Guide Diagnostic OptionsPhone Number Memory Options AT Commands Registers Result Codes Introduction AT Commands, S-Registers, and Result Codes AT Commands DS= y Dial Stored Telephone Number Echo Command Mode CharactersHook Control Information Request Monitor Speaker Mode Monitor Speaker VolumeReturn Online to Data Mode Result Codes Enable/Disable Set Register Value Select RegisterRead Register Value Tone Dialing Result Code Selection Modem ResetLong Space Disconnect Data Carrier Detect DCD Control Load Factory Settings Error Correction ModesData Terminal Ready DTR Control Modem-Initiated Flow Control Flow Control Selection Communications Mode22bis Guard Tone Control Test Commands Sync/Async ModeClear to Send CTS Control Data Set Ready DSR Control Store Current Configuration Display Current ConfigurationDisplay Last Connection Statistics Synchronous Clock Source Line Signal Level Select Profile for Hard ResetZy =x Store Telephone Number Data Compression Control PCM Code Selection Line Signal Quality\An Maximum MNP Block Size \Bn Transmit Break \Vn Single Line Connect Message \Nn Error Correction Mode Selection Reserved,maxTXrateCR +MS= Modulation Selection MNP Extended Services Command #CBNy=x Store Callback Number Command -SDR=nDistinctive Ring ControlCommand #CBPy=x Store Callback Password Flash Memory Download Callback Enable/Disable Command #CID= n Caller IDCommand $SBn Serial Port Baud Rate Escape Sequence Registers Register Unit Range Default Description S32 S36 S46 Terse Verbose Description Result Codes Protocol ALT +FCERROR MultiModemII User Guide Remote Configuration Changing the Remote Configuration Password Basic ProcedureSetup Changing the Remote Escape Character Remote Configuration MultiModemII User Guide Callback Security Turning Callback Security On and Off Setup Procedures Callback Security Assigning Callback Passwords Assigning Callback Phone Numbers Command #CBN y= x Store Callback Number Calling ProcedureCallback Security Commands Command #CBPy=x Store Callback Password Callback Assignments MultiModemII User Guide Leased Line Operation Two-Wire Setup Leased Line Operation Four-Wire Setup Dial Backup and Leased Line Restoral Setup Dial Backup and Leased Line Restoral Leased Line Operation MultiModemII User Guide Solving Problems None of the Indicators Light Solving Problems Modem Does Not Respond to Commands Modem Dials But Cannot Connect Modem4Disconnects While Online File Transfer4Is Slower Than It Should Be Modem4Cannot Connect When Answering Modem4Doesn’t Work with Caller ID Data Is Being LostThere Are Garbage4 Characters on the Monitor Fax and Data4Software Can’t Run at the Same Time Appendixes FCC Part 68 Telecom Appendix a Regulatory Compliance Regulatory Compliance Fax Branding Statement Commission Decision CTR21 Canadian Limitations NoticeInternational Modem Restrictions New Zealand Telecom Warning Notice EMC, Safety, and Terminal Directive Compliance Appendix B Technical Specifications Technical Specifications Receiver Sensitivity Loopback Tests Test procedureLocal Analog Loopback Test V.54 Loop Figure C-2. Remote digital loopback test Remote Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback test Local Digital Loopback Test V.54 Loop Back-to-Back Test Figure C-5. Back-to-back test connections Service Limited Warranty Warranty, Service, and Technical Support Online Warranty RegistrationTechnical Support Multi-Tech BBS About the Internet SupplyNet Online Ordering Instructions Ordering Modem Accessories Identify the Modem Firmware Upgrade Overview Multi-Tech Web Site Identify the Current Firmware VersionMulti-Tech BBS Upgrading the Modem Set the Modem to the Factory Defaults Download the Upgrade FileExtract the Upgrade Files Restore Your Parameters Upgrade the Modem’s Firmware RS-232 Pinouts Appendix F Cable Pinouts Cable Pinouts Leased Line Pinouts Ctrl Code Hex Dec Appendix G Ascii Character Map Index 108 Index 110