Fax Branding Statement | Multi-Tech Systems MT5600BL, MT5600BA

	A Regulatory Compliance
Manufacturer:	Multi-Tech Systems, Inc.
Trade Name	MultiModemII
Model Number:	MT5600BA or MT5600BL
FCC Registration No:	AU7USA-33378-M5-E
Ringer Equivalence No:	0.1A
Modular Jack (USOC):	RJ11C or RJ11W (single line)
Service Center in USA:	Multi-Tech Systems, Inc.
	2205 Woodale Drive
	Mounds View, MN 55112
	(612) 785-3500
	(612) 785-9874 Fax

Fax Branding Statement

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any mes- sage unless such message clearly contains the following information:

•Date and time the message is sent

•Identification of the business or other entity, or other individual sending the message

•Telephone number of the sending machine or such business, other entity, or individual

This information is to appear in a margin at the top or bottom of each transmitted page or on the first page of the transmission. (Adding this information in the margin is referred to as fax branding.)

Since any number of fax software packages can be used with this product, the user must refer to the fax software manual for setup details. Typically the fax branding information must be entered via the configuration menu of the software.

85

Image 93

Multi-Tech Systems MT5600BL, MT5600BA manual Fax Branding Statement, Regulatory Compliance

Contents

Model MT5600BA Model MT5600BL Record of Revisions FCC Part Introduction Using the Front PanelQuick Start MultiModemII User Guide Remote Configuration AT Commands, S-Registers & Result CodesSolving Problems Callback Security Appendix a Regulatory Compliance Appendix D Warranty, Service, and Technical SupportAppendix C Loopback Tests Appendix E Upgrading the Modem Contents Viii Introduction Features IntroductionProduct Description Data Introduction Related Manuals What Is in Your Modem Package? Quick Start What You Will Need Safety WarningsWe supply You supply RS232 Connection Connect the Modem to Your SystemDialup Connection Quick Start Four-Wire Leased Line Connection Two-Wire Leased Line ConnectionPower Connection Power-On Test Install the Modem in Windows Adding the Modem to WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Trio DataComm Call the Multi-Tech BBS Windows HyperTerminal Windows Terminal Send a Fax Trio FaxMicrosoft Fax References Select Start Programs Accessories Fax Compose new fax MultiModemII User Guide Using the Front Panel LED Indicators Modem Configuration Liquid Crystal Display LCD Using the Front PanelOption Selection Menu Structure MultiModemII User Guide Menu Overview Using the Front Panel Status Trunk MultiModemII User Guide Basic Options Trunk Using the Front Panel Advanced Options Trunk Diagnostic Options Trunk MultiModemII User Guide Remote Configuration Options Trunk Caller ID Options Trunk Using the Front Panel Phone Number Memory Options Trunk Status Menu Options Using the Front Panel Basic Options Implemented Advanced Options Remote Configuration Options MultiModemII User Guide Diagnostic Options Phone Number Memory OptionsCaller ID Options AT Commands Registers Result Codes Introduction AT Commands, S-Registers, and Result Codes AT Commands DS= y Dial Stored Telephone Number Echo Command Mode CharactersHook Control Information Request Monitor Speaker Mode Monitor Speaker VolumeReturn Online to Data Mode Result Codes Enable/Disable Set Register Value Select RegisterRead Register Value Tone Dialing Result Code Selection Modem ResetLong Space Disconnect Data Carrier Detect DCD Control Load Factory Settings Error Correction ModesData Terminal Ready DTR Control Modem-Initiated Flow Control Communications Mode 22bis Guard Tone ControlFlow Control Selection Test Commands Sync/Async ModeClear to Send CTS Control Data Set Ready DSR Control Store Current Configuration Display Current ConfigurationDisplay Last Connection Statistics Synchronous Clock Source Line Signal Level Select Profile for Hard ResetZy =x Store Telephone Number Data Compression Control PCM Code Selection Line Signal Quality\An Maximum MNP Block Size \Bn Transmit Break \Vn Single Line Connect Message \Nn Error Correction Mode Selection Reserved,maxTXrateCR +MS= Modulation Selection MNP Extended Services Command #CBNy=x Store Callback Number Command -SDR=nDistinctive Ring ControlCommand #CBPy=x Store Callback Password Flash Memory Download Callback Enable/Disable Command #CID= n Caller IDCommand $SBn Serial Port Baud Rate Escape Sequence Registers Register Unit Range Default Description S32 S36 S46 Terse Verbose Description Result Codes Protocol ALT +FCERROR MultiModemII User Guide Remote Configuration Basic Procedure SetupChanging the Remote Configuration Password Changing the Remote Escape Character Remote Configuration MultiModemII User Guide Callback Security Turning Callback Security On and Off Setup Procedures Callback Security Assigning Callback Passwords Assigning Callback Phone Numbers Calling Procedure Callback Security CommandsCommand #CBN y= x Store Callback Number Command #CBPy=x Store Callback Password Callback Assignments MultiModemII User Guide Leased Line Operation Two-Wire Setup Leased Line Operation Four-Wire Setup Dial Backup and Leased Line Restoral Setup Dial Backup and Leased Line Restoral Leased Line Operation MultiModemII User Guide Solving Problems None of the Indicators Light Solving Problems Modem Does Not Respond to Commands Modem Dials But Cannot Connect Modem4Disconnects While Online File Transfer4Is Slower Than It Should Be Modem4Cannot Connect When Answering Data Is Being Lost There Are Garbage4 Characters on the MonitorModem4Doesn’t Work with Caller ID Fax and Data4Software Can’t Run at the Same Time Appendixes FCC Part 68 Telecom Appendix a Regulatory Compliance Regulatory Compliance Fax Branding Statement Canadian Limitations Notice International Modem RestrictionsCommission Decision CTR21 New Zealand Telecom Warning Notice EMC, Safety, and Terminal Directive Compliance Appendix B Technical Specifications Technical Specifications Receiver Sensitivity Test procedure Local Analog Loopback Test V.54 LoopLoopback Tests Figure C-2. Remote digital loopback test Remote Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback test Local Digital Loopback Test V.54 Loop Back-to-Back Test Figure C-5. Back-to-back test connections Service Limited Warranty Warranty, Service, and Technical Support Online Warranty RegistrationTechnical Support Multi-Tech BBS About the Internet SupplyNet Online Ordering Instructions Ordering Modem Accessories Identify the Modem Firmware Upgrade Overview Multi-Tech Web Site Identify the Current Firmware VersionMulti-Tech BBS Upgrading the Modem Download the Upgrade File Extract the Upgrade FilesSet the Modem to the Factory Defaults Restore Your Parameters Upgrade the Modem’s Firmware RS-232 Pinouts Appendix F Cable Pinouts Cable Pinouts Leased Line Pinouts Ctrl Code Hex Dec Appendix G Ascii Character Map Index 108 Index 110