Log into the CLI, To log into the CLI | Net Optics Director manual

Director

3. Enter customer to log into the shell. The shell asks for the password.

login as: customer customer@10.60.4.180's password:

Figure 13: Shell login

4.Enter netoptics as the password. For security, the password is not displayed as you type it. The Director CLI runs and the CLI sign-on banner and login prompt are displayed.

login as: customer customer@10.60.4.8's password:

Last login: Thu Sep 4 09:40:31 2008 from 10.30.1.62

**********************************************************
*	Net Optics Command Line Interface (CLI)		*
*	Copyright (c) 2008 by Net Optics, Inc.		*
*	Copyright (c) 2008 by Net Optics, Inc.		*
*		Restricted Rights Legend	*
*		Restricted Rights Legend	*
*			*
* Use,	duplication, or disclosure by the Government is *
* subject		to restrictions as set forth in subparagraph *
* (c)	of	the Commercial Computer Software - Restricted *
* Rights		clause at FAR sec. 52.227-19 and subparagraph *
* (c)(1)(ii) of the Rights in Technical Data and Computer*
* Software clause at DFARS sec. 252.227-7013.			*
*		Net Optics, Inc.	*
*		Net Optics, Inc.	*
*		5303 Betsy Ross Drive	*
*		Santa Clara, California 95054 USA	*
*		+1-408-737-7777	*
*			*

**********************************************************

login user:

Figure 14: Shell login as customer (password "netoptics" is not displayed)

Log into the CLI

Each Director maintains a list of accounts for users authorized for access to that particular Director. The default account for new systems is User Name admin and Password netoptics.

To log into the CLI:

1.Enter the user name. (The default user name is admin.) The Enter Password prompt is displayed.

2.Enter the password. (The default password is netoptics.) For security, the password is not displayed as you type it.

The CLI prompt is displayed.

login user: admin password:

Net Optics>

Figure 15: Logging into the CLI

16

Image 20

Net Optics Director manual Log into the CLI, To log into the CLI

Contents

Data Monitoring Switch Trademarks and Copyrights Contents Chapter Configuring Filters Using the CLI ChapterAppendix a Appendix B Chapter Introduction Key Features Ease of UseMonitor port Filtering Passive, Secure Technology About this Guide Description Director Architecture Director internal architecture USB port Director Management Typical Application Network Links Monitoring Tools 10 Gigabit in-line network connection using a network Tap In-line Monitoring of 10 Gigabit Links Power LEDs Director Front PanelMonitor Port LEDs DNM / Network Port LEDs Director Rear Panel XFP Chapter Installing Director Plan the Installation Unpack and Inspect the Director device Rack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect Power to Director Connect the local CLI Interface Connect the remote CLI Interface Baud Data bits No parity 1 stop bit No flow controlTip To connect the CLI for remote use over the Management port Log into the CLI To log into the CLI To change the login password Configure Director using the CLIChange Director Password To change the port mode Assign a New Manager IP AddressTo assign a new Manager IP address to Director Change Port Modes Save and Load Director Configurations Set the Current Date and Time Using the CLI Help Command To view CLI help information Using the CLI Command History Buffer Show name show running, factory, default, or file name Connect Span Ports to Director To connect a Span port Connect Director With In-line Network Links To connect an in-line network link Connect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Chapter Configuring Filters Using the CLI Syntax Enter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor Port Regenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5 Create Filters To create a filter that selects IPv4 packets by protocol Create Complex Filters Logical and filter connection View filters UDP Work with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network ports XFP Port Protocol = Monitor Port Understand filter interactions CAM Flow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1 To change the Director filter configuration Understand pending and active filters Filter running command Enter filter list to view the pending filter list Filter capacity Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Daisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassis Specifications, DNM EnvironmentalCertifications Available Models Appendix B Command Line Interface Command Sub-Command Arguments Example and description Commit Filter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Director Filter Parameters Qual Value Example Description Vlan=128 Appendix C Protocol Numbers Num Keyword Protocol Mobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved