Quit | Net Optics Director instruction

Director

Command	Sub-Command	Arguments	Example and description

quit			quit
			Exits the CLI shell (same as exit and logout)
			Note: To maintain system security, control is not
			returned to the command shell.

reset			reset
			Reboots the Director device; also called warm boot;
			similar to power-cycling the device; reloads the
			default configuration

save		<filename>	save my_configuration-1
			Arguments:
			<filename> is the name of the file where the
			configuration is saved; a string; do not include an
			extension
			Saves the Director device configuration to a file;
			saved information includes port set-up and filters

show		running factory	show my_configuration-1
		<filename>	Arguments:
			running to show configuration that is currently
			operating
			factory to show configuration set at the factory
			<filename> is the name of a saved configuration
			file to display; a string; do not include an extension
			Displays the contents of the specified configuration
			or saved configuration file (see save command)

stats	clear	ports=all<[portlist>	stats clear ports=all
			Clears RMON statistics for the designated ports

	show	ports=all<[portlist>	stats show ports=m.2,n1.4
			Displays RMON statistics for the designated ports

sysip	commit		sysip commit
			Activates pending changes defined with sysip set

	discard		sysip discard
			Clears any pending changes defined with sysip set

	set	ipaddr=<address>	sysip set ipaddr=192.168.1.2 mask=255.255.0.0>
		mask=<netmask>	Arguments:
		gw=<gateway>	<address> is the IP address (default: 192.168.1.2)
			<mask> is the netmask (default: 255.0.0.0)
		Note: All three arguments are	<gateway> is the gateway IP address (default:
		required	192.168.1.1)
			Sets the Director IP address, netmask, and gateway
			IP address; requires a sysip commit command to
			activate the new settings

	show		sysip show
			Displays the current Director IP address information,
			as well as any pending IP address information that
			was set with a sysip set command

47

Image 51

Net Optics Director manual Quit

Contents

Data Monitoring Switch Trademarks and Copyrights Contents Appendix B Chapter Configuring Filters Using the CLIChapter Appendix a Chapter Introduction Passive, Secure Technology Key FeaturesEase of Use Monitor port Filtering Description About this Guide Director internal architecture Director Architecture Director Management USB port Network Links Typical Application Monitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network Tap DNM / Network Port LEDs Power LEDsDirector Front Panel Monitor Port LEDs XFP Director Rear Panel Chapter Installing Director Unpack and Inspect the Director device Plan the Installation Install Director Network Modules Install SFP and XFP Monitor port ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to Director To connect the CLI for remote use over the Management port Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control Tip To log into the CLI Log into the CLI Configure Director using the CLI Change Director PasswordTo change the login password Change Port Modes To change the port modeAssign a New Manager IP Address To assign a new Manager IP address to Director Set the Current Date and Time Save and Load Director Configurations To view CLI help information Using the CLI Help Command Show name show running, factory, default, or file name Using the CLI Command History Buffer To connect a Span port Connect Span Ports to Director To connect an in-line network link Connect Director With In-line Network Links Configure a Matrix Switch connection in Director Check the InstallationConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLI Copy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activated Lter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor Ports To create a filter that selects IPv4 packets by protocol Create Filters Logical and filter connection Create Complex Filters UDP View filters Configurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit ports XFP Port Protocol = Monitor Port CAM Understand filter interactions Flow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filters Understand pending and active filters To change the Director filter configuration Filter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacity Daisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director Specifications Available Models Specifications, DNMEnvironmental Certifications Appendix B Command Line Interface Commit Command Sub-Command Arguments Example and description Filter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example Description Num Keyword Protocol Appendix C Protocol Numbers Mobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved