Manuals / NetComm / Computer Equipment / Network Card

NetComm V110 manual Software Configuration, Easy Setup Utility for Windows Only

Models: V110

1 68

Download 68 pages 17.11 Kb

Page 11

Software Configuration

Easy Setup Utility (for Windows Only)

1.For easy configuration, insert the included CD into your CD-ROM drive. The CD should auto-start. If it does not start, click on Start -> Run and type in D:\Easysetup\vbpES.exe (where D is the drive letter of your CD-ROM drive).

2.The default Internet access is DHCP Client Mode. Click on WAN Configuration to change the internet access type.

3.Enter the SIP Proxy Domain, Proxy Server, Outbound Proxy, Username, Auth. ID and Auth. Password provided by your VSP.

4.And then click on Setup, the software will start to configure the NetComm ATA. Follow the instructions of the Easy Setup utility which will guide you to complete the configuration.

5.After a few minutes, the NetComm ATA should report that the setup has been successful.

Note: The easy setup utility can not be used to retrieve details. The utility will initialize the unit back to default settings when executed.

YML881Rev1	�V110,��V2��10P,��V2��11,��V220�� User Guide
www.netcomm.com.au	11

Image 11

NetComm V110 manual Software Configuration, Easy Setup Utility for Windows Only

Contents

User Guide Page Welcome to the Wonderful World of VoIP VoIP ATA Features Minimum System Requirements Package ContentsPort / Button Description ResetGetting to know your NetComm V2xx ATA Ports and ButtonsETH LED IndicatorsPWR SIPDhcp Default SettingsRestoring Factory Defaults V211 and V210P Hardware InstallationV110 V220 V110,V210P,V211,V220 User Guide Easy Setup Utility for Windows Only Software ConfigurationAccessing the web configuration Configuration via a web browserWAN Configuration MAC Static IP ConfigurationOption Description YML881Rev1 Ethernet MAC address of the WAN interface. Optional Dhcp ModeYour Internet Service Provider ISP. Optional User Name PPPoE Client ModeVoIP Configuration Field Description Advanced Configuration VoIP Status StatusSystem Information Network StatusWAN ConfigurationOptions Description VoIP SIP Setting Support DNS SRV RTP Port Base port to receive RTP packets. DefaultAuth Name Use DNS SRVCodec Settings V110,V210P,V211,V220 User Guide URL Phone Book ConfigurationPhone Book Example 2 Position 1, Name ip address 10.32, Number 001, URL Add New PhoneYML881Rev1 IP/ON Phone SettingYML881Rev1 V110,V210P,V211,V220 User Guide DND Always Volume Setting functionTo set the volume for on your handset V211 only is to set the Pstn volume outV110,V210P,V211,V220 User Guide Enter the correct PIN Code 1234, then press # How to Use VoIP to Pstn Call Call in via VoIPHow to Use Pstn to VoIP Call Call in via Pstn CID Type Enable to detect the Caller ID Type Single Caller ID Enable to detect Single Caller IDEnable to detect the Caller ID without time 2,3,4,5,6,7,8,9 Wildcard Drop PrefixDialed V110,V210P,V211,V220 User Guide YML881Rev1 FAX Switch on to enable T.38 fax supportPort Default is Auto Dial Time functionSupport Others Enable Auto Configuration. DefaultoffYML881Rev1 Supports the proprietary implementation DefaultWALKERSUN2 Computer’s MAC that was originally set up for such an ISPOptions Description MAC Clone Ddns 110, V2 10P, V2 11, V220 User Guide CFI Vlan SettingsMapping 23 that can be set Default page is Page1. There are 3 pages, Page 1 toVirtual Server NumSeen from the WAN side Add the new Server which you configuredAdd Virtual Server POP3 Well Known TCP/UDP PortsUDP TCP SmtpIf the primary server becomes unreachable Sntp SettingsAlarm Settings System Authority Save Settings/RebootSystem Reset factory defaultFirmware Update Firmware Auto UpdateUpdate via Server TFTP, FTP or HttpAutomatically Notify Only Auto Update ProcedureDisplays the next update or check time Be notedGroup IVR Action IVR Menu Choice Parameters IVR Interface for VoIP GatewayDial a Pstn Phone call V210P/V211 How to make a phone callCall Features Dial a VoIP Phone callCall Hold Way ConferencingCall Waiting ETH light is off Common problem and solutionsNo power to the ATA Please ensure that the power cable is connected correctlyATA Appendix a GlossaryLimitations of Warranty Product WarrantyV110,V210P,V211,V220 User Guide Your ADSL2+ connection Email support@netcomm.com.au Product Warranty Contact Information