V110,V210P,V211,V220 User Guide | NetComm specs

DTMF Setting

You can set the Out of Band DTMF and Send DTMF SIP Info Enable/Disable in this page. To change this setting, please follow your VoIP Service Provider’s information. When you finished the setting, please click the Submit button.

•RFC 2833: Click this button to send mid-call DTMF tones in RTP packets separately using RFC2833, i.e., dynamic negotiation of RTP payload for DTMF digits will be done.

•Inband DTMF (IN AUDIO): Click this button to send mid-call DTMF tones in RTP packets with the same payload as voice, i.e., dynamic payload negotiation for DTMF digits will not be done.

•Send DTMF SIP Info: This field is configurable when RFC 2833 is selected as the DTMF relay mechanism. Specify the payload number that needs to be used for DTMF information negotiated in SDP during SIP signaling.

RPort Function

You can enable or disable the RPort feature in this page. To change this setting, please follow the recommendation of your VSP.

QoS

You can configure the Hold by RFC and Voice/SIP QoS in this page.

The QoS setting is to set the voice packets priority. If you set the value higher than 0, then the voice packets will get the higher priority to the Internet. But the QoS function still needs to cooperate with the others Internet devices.

V110,V2�10P,V2�11,V220� User Guide	YML881Rev1
28	www.netcomm.com.au

Image 28

NetComm manual V110,V210P,V211,V220 User Guide

Contents

User Guide Page Welcome to the Wonderful World of VoIP VoIP ATA Features Package Contents Minimum System Requirements Reset Getting to know your NetComm V2xx ATAPorts and Buttons Port / Button Description LED Indicators PWRSIP ETH Restoring Factory Defaults Default SettingsDhcp Hardware Installation V211 and V210P V110 V220 V110,V210P,V211,V220 User Guide Software Configuration Easy Setup Utility for Windows Only Configuration via a web browser Accessing the web configuration WAN Configuration Option Description Static IP ConfigurationMAC YML881Rev1 Your Internet Service Provider ISP. Optional Dhcp ModeEthernet MAC address of the WAN interface. Optional PPPoE Client Mode User Name VoIP Configuration Field Description Advanced Configuration Status System InformationNetwork Status VoIP Status Configuration WAN Options Description VoIP SIP Setting RTP Port Base port to receive RTP packets. Default Auth NameUse DNS SRV Support DNS SRV Codec Settings V110,V210P,V211,V220 User Guide Phone Book Phone Book ConfigurationURL Add New Phone Example 2 Position 1, Name ip address 10.32, Number 001, URL YML881Rev1 Phone Setting IP/ON YML881Rev1 V110,V210P,V211,V220 User Guide Volume Setting function To set the volume for on your handsetV211 only is to set the Pstn volume out DND Always V110,V210P,V211,V220 User Guide How to Use Pstn to VoIP Call Call in via Pstn How to Use VoIP to Pstn Call Call in via VoIPEnter the correct PIN Code 1234, then press # Enable to detect the Caller ID without time Single Caller ID Enable to detect Single Caller IDCID Type Enable to detect the Caller ID Type Dialed Drop Prefix2,3,4,5,6,7,8,9 Wildcard V110,V210P,V211,V220 User Guide YML881Rev1 Switch on to enable T.38 fax support Port Default isAuto Dial Time function FAX Support Enable Auto Configuration. Defaultoff Others YML881Rev1 Default Supports the proprietary implementation Options Description MAC Clone Computer’s MAC that was originally set up for such an ISPWALKERSUN2 Ddns 110, V2 10P, V2 11, V220 User Guide Vlan Settings CFI Default page is Page1. There are 3 pages, Page 1 to Virtual ServerNum Mapping 23 that can be set Add Virtual Server Add the new Server which you configuredSeen from the WAN side Well Known TCP/UDP Ports UDP TCPSmtp POP3 Sntp Settings If the primary server becomes unreachable Alarm Settings Save Settings/Reboot System Authority Firmware Update Reset factory defaultSystem Auto Update Update viaServer TFTP, FTP or Http Firmware Notify Only Auto Update Procedure Displays the next update or check timeBe noted Automatically IVR Interface for VoIP Gateway Group IVR Action IVR Menu Choice Parameters How to make a phone call Call FeaturesDial a VoIP Phone call Dial a Pstn Phone call V210P/V211 Call Waiting Way ConferencingCall Hold Common problem and solutions No power to the ATAPlease ensure that the power cable is connected correctly ETH light is off Appendix a Glossary ATA Product Warranty Limitations of Warranty V110,V210P,V211,V220 User Guide Your ADSL2+ connection Product Warranty Contact Information Email support@netcomm.com.au