Manuals / NETGEAR / Computer Equipment / Network Router

NETGEAR WAB102 manual Change the SSID

Models: WAB102

1 49

Download 49 pages 27.79 Kb

Page 40

Image 40

User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access Point

Change the SSID

Follow the steps below:

1.From the Windows desktop, follow the instructions given in “Basic Configuration“ on page 14 to go to the Setup window.

2.To change the SSID, enter a new SSID.

Note: The characters are case sensitive. An access point always functions in infrastructure mode. The SSID for any wireless device communicating with the access point must match the SSID configured in the access point.

3.Click Apply or OK for the changes to take effect.

Protecting Your Wireless Network

Page 40

Image 40

Contents

User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access Point NETGEAR, IncNETGEAR, INC Technical SupportTrademarks Statement of ConditionsContents Setting Up Basic Wireless ConnectivityProtecting Your Wireless Network TroubleshootingAbout the Wireless Access Point Chapter IntroductionFeatures BenefitsSystem Requirements What’s In the Box? Compatible and Related NETGEAR Products802.11a+b Standards-based Wireless Networking Hardware DescriptionWAB102 Wireless Access Point Front Panel User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access PointPower EthernetWAB102 Wireless Access Point Rear Panel Power SocketRestore to Factory Default Button Power Adapter Cable HolderChapter 2 Setting Up Basic Wireless Connectivity To install your WAB102, see “Installation Overview“ on pagePlacement and Range Guidelines What You Will Need Before You BeginInstall the WAB102 Wireless Access Point Installation OverviewCabling Requirements 1. Position and mount the WAB102 Dual Band Wireless Access Point 3. Connect the power cable4. Configure the wireless adapter settings Wireless6. Verify wireless connectivity to your network 5. Verify the installation was successfulHaving problems? Refer to Chapter 4, “Troubleshooting” Default Factory Settings 1. Determine the name of your access point Basic Configuration2. Open a web browser such as Internet Explorer or Netscape Navigator Configure Basic Setup Parameters Log In to the Access PointHaving problems? Refer to Chapter 4, “Troubleshooting” For LAN parameters, see “TCP/IP Configuration Parameters“ on page 1. Click on the Setup link on the AP Setup menuTCP/IP Configuration Parameters The access point will get the IP address, subnet802.11a Wireless LAN Configuration Parameters User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access PointSetting Up Basic Wireless Connectivity CONFIGURATION802.11b Wireless LAN Configuration Parameters User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access PointSetting Up Basic Wireless Connectivity CONFIGURATIONChange Password Security Configuration 2. Click Security on the AP Setup menu and log in3. Choose Your Authentication Method 1. Use a browser to connect to the WAB1024. Set Up 802.11a Encryption Security as Needed 5. Set Up 802.11b Encryption Security as NeededFor 64-bits encryption For 128-bits encryption802.11a Wireless LAN Security Parameters User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access PointSetting Up Basic Wireless Connectivity CONFIGURATION802.11b Wireless LAN Security Parameters User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access PointSetting Up Basic Wireless Connectivity CONFIGURATIONAccess Control Firmware Upgrade Access Control Configuration ParametersAdvanced Setup 802.11a Advanced Wireless LAN Configuration Parameters User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access PointSetting Up Basic Wireless Connectivity CONFIGURATION802.11b Advanced Wireless LAN Configuration Parameters User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access PointSetting Up Basic Wireless Connectivity CONFIGURATIONRestore Factory Default To restore factory default settings, complete the followingUser’s Guide for the WAB102 802.11a+b Dual Band Wireless Access Point Setting Up Basic Wireless ConnectivityAP Status Station List About User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access Point Setting Up Basic Wireless ConnectivityChapter 3 Protecting Your Wireless Network Enabling Basic Wireless Access Security FeaturesSecure the Access Point Change the PasswordBefore You Change the SSID and WEP Settings 802.11a WEP Encryption Keys 802.11b WEP Encryption KeysAuthentication WEP EncryptionChange the SSID Configure WEP Encryption Restrict Wireless Activity by MAC Address User’s Guide for the WAB102 802.11a+b Dual Band Wireless Access Point Protecting Your Wireless NetworkChapter Troubleshooting No lights are lit on the access pointGo to “Install the WAB102 Wireless Access Point“ on page Basic FunctioningOne or both of the wireless activity lights do not light up The Ethernet Link/Act light is not litUser’s Guide for the WAB102 802.11a+b Dual Band Wireless Access Point TroubleshootingTrademarks Statement of ConditionsFCC Warning ComplianceRF Exposure Requirements Radio Frequency Interference RequirementsCanadian Department of Communications Radio Interference Regulations Regulatory Compliance InformationNETGEAR, Inc