Manuals / Nortel Networks / Computer Equipment / Switch

Nortel Networks 5000BH TokenSpeed Module Startup Failure, Remove and reinsert the failing module

Models: 5000BH

1 70

Download 70 pages 41.38 Kb

Page 47

9.Click on the Start button in the Software Download dialog box.

Troubleshooting the TokenSpeed Module

9.Click on the Start button in the Software Download dialog box.

If the display returns to the Main Menu instead of displaying the “Writing to Flash” message, the download process did not complete successfully.

10.If you are not prompted to reset the switch, choose Discover again.

11.Click on the icon for the switch and choose Download software.

When the download is complete, the following message is displayed:

Writing to Flash...

The switch begins executing the loaded switch image and prompts you to reset the switch.

12.Choose Reset to verify that the downloaded image is installed properly.

When the switch completes the reset and starts operating properly, you may continue normal operation. If the reset is unsuccessful or an error indication appears, repeat the entire procedure. If it fails again, call Bay Networks customer support. Please be ready to provide the service representative with the information listed on page 4-1.

TokenSpeed Module Startup Failure

Symptom: The switch startup process completes successfully, but the Activity LED blinks continually.

To resolve the problem, follow these steps:

1.Check all modules in the chassis to make sure they are ﬁrmly seated and that the retaining screws are tight.

2.Remove and reinsert the failing module.

If the problem persists, contact Bay Networks customer support. Please be ready to provide the service representative with the information listed on page 4-1.

893-01019-A

4-3

Image 47

Nortel Networks 5000BH TokenSpeed Module Startup Failure, Click on the Start button in the Software Download dialog box

Contents

Part No. 893-01019-A June Using the 8-port TokenSpeed and TokenSpeed/MCP Switch ModulesEN 55 022 Declaration of Conformance TrademarksStatement of Conditions Federal Communications Commission FCC Statement893-01019-A Voluntary Control Council for Interference VCCI StatementDeclaration of Conformity Bay Networks, Inc. Software License Agreementc that the operation of the Software will be uninterrupted or error free, or d that all defects in the operation of the Software will be corrected. Bay Networks is not obligated to remedy any Software defect that cannot be reproduced with the latest Software release. These warranties do not apply to the Software if it has been i altered, except by Bay Networks or in accordance with its instructions ii used in conjunction with another vendor’s product, resulting in the defect or iii damaged by improper environment, abuse, misuse, accident, or negligence. THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Licensee is responsible for the security of its own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost or altered ﬁles, data, or programs 8. Export and Re-export. Licensee agrees not to export, directly or indirectly, the Software or related technical data or information without ﬁrst obtaining any required export licenses or other governmental approvals. Without limiting the foregoing, Licensee, on behalf of itself and its subsidiaries and afﬁliates, agrees that it will not, without ﬁrst obtaining all export licenses and approvals required by the U.S. Government i export, re-export, transfer, or divert any such Software or technical data, or any direct product thereof, to any country to which such exports or re-exports are restricted or embargoed under United States export control laws and regulations, or to any national or resident of such restricted or embargoed countries or ii provide the Software or related technical data or information to any military end user or for any military end use, including the design, development, or production of any chemical, nuclear, or biological weapons 893-01019-A Overview of the TokenSpeed Module ContentsPreface ChapterAppendix A Chapter Installing and Connecting the TokenSpeed ModuleTroubleshooting the TokenSpeed Module ChapterFigures Station to hub connection RJ-45 to IBM Type Tables 893-01019-A Audience PrefacePurpose Special Message Formats Two-tiered Procedure FormatConventions Model 5000BH Switches Related PublicationsOrdering Bay Networks Publications Using SpeedView 2.1 for WindowsBay Networks Customer Support How to Get Helpxvii For More InformationPreface 893-01019-A Using the 8-port TokenSpeed and TokenSpeed/MCP Switch Modulesxviii About the TokenSpeed Module Chapter Overview of the TokenSpeed ModuleTokenSpeed Module Ports and Connectivity FeaturesNetwork Management Fault ToleranceFiltering Caching and ProxyFigure 1-1. Hardware features of the TokenSpeed module Physical DescriptionGiving a Server a Dedicated Port Chapter TokenSpeed Module ApplicationsFigure 2-1. Giving a server a dedicated port Segmenting a RingTokenSpeed Module Applications Connecting a Segment Through the RI or RO PortBefore Connecting a Segment Using a Lobe PortUsing the 8-port TokenSpeed and TokenSpeed/MCP Switch Modules Figure 2-3. Connecting ring segments through lobe portsFigure 2-4. Replacing a source route bridge or router Replacing a Source Route Bridge or RouterConcentrating Rings into a Router 7571EA Figure 2-5. Concentrating multiple rings into a routerPreparing for Installation Chapter 3 Installing and Connecting the TokenSpeed Module1. Remove the ﬁller panel Installing the TokenSpeed ModuleFigure 3-1. Removing a ﬁller panel Figure 3-2. Inserter/extractor levers ready for installationFigure 3-4. Inserting the module into the chassis Figure 3-3. Slot module guidesConnecting Cables to TokenSpeed Ports Table 3-1. Port types for the TokenSpeed module Token Ring ConnectionsManagement Connection Verifying the InstallationTokenSpeed LED Switch Startup SequenceTokenSpeed Module LEDs Factory default conﬁguration settings Conﬁguring the TokenSpeed Module893-01019-A Using the 8-port TokenSpeed and TokenSpeed/MCP Switch ModulesFactory default conﬁguration settings continued 3-10Windows Removing and Replacing a ModuleReplacing a TokenSpeed/MCP Module 6. Slide the module out of the chassis see Figure Replacing a TokenSpeed Module 5. Slide the module out of the chassis see Figure Page Chapter 4 Troubleshooting the TokenSpeed Module Switch Startup Failure with TokenSpeed/MCP 2. Remove and reinsert the failing module TokenSpeed Module Startup Failure11. Click on the icon for the switch and choose Download software 9. Click on the Start button in the Software Download dialog box2. Verify that the cabling is correct Port Insertion Problems3. Using SpeedView, verify the following items 4. Disable the port then enable it again Page Appendix A Technical Speciﬁcations Environmental Speciﬁcations Using the 8-port TokenSpeed and TokenSpeed/MCP Switch ModulesSafety Agency Approvals ConnectorsAppendix B Cables Cable Types Port TypesCable distances Token Ring Connectors on the TokenSpeed ModuleFigure B-1. RJ-45 connector on the TokenSpeed module Table B-2Figure B-2. Connectors for token ring network cables Cable and Connector Pin AssignmentsRJ-45 to RJ-45 Connection 7603EB Using the 8-port TokenSpeed and TokenSpeed/MCP Switch ModulesFigure B-4. Station to hub connection RJ-45 to RJ-45 Figure B-5. Bay/SNPX RO to RI connection RJ-45 to RJ-457684EB CablesFigure B-6. RI-other to RO connection RJ-45 to RJ-45 Figure B-7. RO-other to RI connection RJ-45 to RJ-45RJ-45 to DB-9 Connection 7607EB CablesFigure B-9. Station to hub connection RJ-45 to DB-9 Figure B-10. Bay/SNPX RO to RI connection RJ-45 to DB-9B-10 Using the 8-port TokenSpeed and TokenSpeed/MCP Switch ModulesFigure B-11. RI-other to RO connection RJ-45 to DB-9 Figure B-12. RO-other to RI connection RJ-45 to DB-9RJ-45 to IBM Type 1 Connection B-12 Using the 8-port TokenSpeed and TokenSpeed/MCP Switch ModulesFigure B-14. Bay/SNPX RO to RI connection RJ-45 to IBM Type Figure B-15. RI-other to RO connection RJ-45 to IBM TypeSerial MCP Connections B-14 Using the 8-port TokenSpeed and TokenSpeed/MCP Switch ModulesTable B-4 Female DB-25 to female DB-9 adapterIndex-1 Indextypes, B-2 caching, RIF RJ-45, 1-1, 3-6, B-3Index-2 LEDsIndex-3 TFTP