Cable and Connector Pin Assignments | Nortel Networks 5000BH

Using the 8-port TokenSpeed and TokenSpeed/MCP Switch Modules

Cable and Connector Pin Assignments

This section provides the pin assignments for connectors typically used to connect network devices to the TokenSpeed module. For each connection type, the illustrations show the TokenSpeed port type, pin numbers, signal, and phantom source. All cables are shown as straight-through cables because the correct port type setting on the TokenSpeed module automatically adjusts the port for any needed crossover function.

The end that connects to the TokenSpeed module is an RJ-45 connector. The connector at the other end can be another RJ-45 connector, a DB-9 connector, or an IBM Type 1 connector (see Figure B-2).

1 2 3 4 5 6 7 8

5 1

Pin 1 (Black)

9 6

4026

7578EA

3041FC

Figure B-2. Connectors for token ring network cables

B-4	893-01019-A

Image 56

Nortel Networks 5000BH manual Cable and Connector Pin Assignments, Figure B-2. Connectors for token ring network cables

Contents

Using the 8-port TokenSpeed TokenSpeed/MCP Switch Modules Trademarks Statement of Conditions Voluntary Control Council for Interference Vcci Statement Iii 893-01019-A 893-01019-A 893-01019-A Contents Chapter Installing and Connecting the TokenSpeed Module Figures Figure B -11. RI-other to RO connection RJ-45 to DB-9 Tables Xii Audience PrefacePurpose Special Message Formats Two-tiered Procedure FormatConventions Related Publications Ordering Bay Networks PublicationsRelated publications Title Description How to Get Help Technical Solutions Center Telephone number Fax numberBay Networks Customer Support Region Telephone number Fax number For More Information 893-01019-A Chapter Overview of the TokenSpeed Module About the TokenSpeed Module Features TokenSpeed Module Ports and Connectivity Fault Tolerance FilteringCaching and Proxy Network Management Hardware features of the TokenSpeed module Physical Description Chapter TokenSpeed Module Applications Giving a Server a Dedicated Port Segmenting a Ring Giving a server a dedicated port Connecting a Segment Through the RI or RO Port Connecting a ring segment through an RI/RO port ring segment Connecting a Segment Using a Lobe Port Connecting ring segments through lobe ports Replacing a Source Route Bridge or Router Concentrating Rings into a Router Concentrating multiple rings into a router Installing and Connecting the TokenSpeed Module Preparing for Installation Installing the TokenSpeed Module Removing a ﬁller panel Slot module guides Connecting Cables to TokenSpeed Ports Seating the module Network device port TokenSpeed port type Token Ring ConnectionsPort types for the TokenSpeed module Verifying the Installation Management Connection LED name Meaning LED Switch Startup SequenceTokenSpeed Module LEDs Conﬁguring the TokenSpeed Module Factory default conﬁguration settingsParameter Factory default Possible settings FFE Removing and Replacing a Module Replacing a TokenSpeed/MCP Module Loosening the TokenSpeed module Slide the module out of the chassis see Figure Replacing a TokenSpeed Module 11. Loosening the TokenSpeed module 12. Removing the module from the Centillion chassis Page Troubleshooting the TokenSpeed Module Switch Startup Failure with TokenSpeed/MCP TokenSpeed Module Startup Failure Port Insertion Problems Verify that the cabling is correct Troubleshooting the TokenSpeed Module Page Appendix a Technical Speciﬁcations Safety Agency Approvals ConnectorsEnvironmental Speciﬁcations Electromagnetic Emissions Appendix B Cables Table B-1 Port types for the TokenSpeed module Port TypesCable Types Token Ring Connectors on the TokenSpeed Module Table B-2 Cable distancesCable type Mb/s 16 Mb/s UTP cable type STP cable type Cable and Connector Pin Assignments Figure B-2. Connectors for token ring network cables RJ-45 to RJ-45 Connection Figure B-3. Hub to station connection RJ-45 to RJ-45 Figure B-4. Station to hub connection RJ-45 to RJ-45 Figure B-6. RI-other to RO connection RJ-45 to RJ-45 RJ-45 to DB-9 Connection Figure B-8. Hub to station connection RJ-45 to DB-9 Figure B-9. Station to hub connection RJ-45 to DB-9 Figure B-11. RI-other to RO connection RJ-45 to DB-9 RJ-45 to IBM Type 1 Connection Figure B-13. Station to hub connection RJ-45 to IBM Type Figure B-14. Bay/SNPX RO to RI connection RJ-45 to IBM Type Male Mini DIN Signal Male DB-25 Pin locations Pin numbers Serial MCP ConnectionsMale Mini DIN 8 to male DB-25 cable Table B-3 Request to send Clear to send Ring indicator Table B-4 Female DB-25 to female DB-9 adapter Index Types, B-2 caching, RIF Index-2 Index-3