Panasonic AG-MX70P manual System1 setting, System2 setting, Bus setting

[Setup] initial setting screen

[System1] setting

This is used to perform a variety of settings.	R1	R2	R3	R4	R5
The rotary 2 control is used to set the amount of delay for	System1	Dly	Time	GPI	RS422
the source input when the [AdvRef] advanced reference		1Frame	Sec	ME	GVG
signal is connected with the 3D optional board (AG-VE70)
		1Frame	Sec	ME	GVG
installed. If 0Frame is selected, the video delay amount is
		0Frame	Frame	DSK	SONY
different between when the 3D effects are applied and when
				Fade
they are not. The default setting is 1Frame. The setting is
fixed at 0Frame when the 3D optional board is not installed.

The audio source delay amount is also set according to this setting.

[Sec] (seconds + frames) or [Frame] (frames) only is selected for the time display using the rotary 3 control. The default setting is [Sec].

Whether [ME], [DSK] or [Fade] is to be executed by GPI can be set using the rotary 4 control. The default setting is [ME]. [GVG] or [SONY] can be selected as the RS-422A protocol using the rotary 5 control. The default setting is [GVG].

[System2] setting

The time taken until the LCD is set to the power saving	R1		R2	R3	R4	R5
mode can be selected using the rotary 2 control.	System2		LCDStby	VBClean	DR	Chr.Lmt
With the 0 setting, the display is always on. The time can		0		Off	On	Off
be set in 10-minute increments from 0 to 60. The default
			0 - 60	On	On	On
setting is 0.
				Off	Off	Off
[On] or [Off] is selected using the rotary 3 control to set
whether or not cleaning is to be performed inside the vertical
blanking period (VBlk). The default setting is [Off].

[On] or [Off] is selected using the rotary 4 control to set whether or not the [DR] (dynamic rounding) is to be performed. The default setting is [On].

[On] or [Off] is selected using the rotary 5 control to set whether restrictions are to be applied to the SDI and component output chroma. If [On] has been selected, the chroma is restricted by the 100% color bar level. The default setting is [Off].

<Note>

Selecting [Off] for [VBClean] may result in a deviation in the amount of delay between the video signals and vertical blanking signals depending on the setting for the [Dly] item among the [System1] settings and on whether the 3D optional board (AG- VE70) has been installed.

[Bus] setting

AB (AB bus) or PrgPre (program/preset system) can be	R1	R2	R3	R4		R5
selected as the bus system using the rotary 2 control. The	Bus	Type	Still	Audio		Tally
default setting is AB.		AB	On	CP	8
[On] (initiate Still) or [Off] (do not initiate Still) when cross
		AB	On	CP		8
points are to be changed is selected using the rotary 3
		Prg Pre	Off	1, 2		EXT
control. The default setting is [On].
The Audio MIX system can be selected using the rotary 4
control.

At the [CP] setting, two audio sources allocated to the selected cross point are output. At the [1,2] setting, the audio sources 1, 2 allocated to the cross point are mixed at all times. The default setting is [CP].

[8]or [EXT] can be selected using the rotary 5 control as the setting for the eight tally outputs. At the [8] setting, the tally signal is output when cross point 8 has been selected; at the [EXT] setting, it is output when EXT has been selected.

<Note>

When [Still] has been set to [Off], the picture may be disturbed if direct switching is performed between SDI/composite and YC/component. This setting must always be used with either an SDI-only/composite system or YC-only/component-only system.

56