Controls and Their Functions

Video monitor

Front panel

12

 

 

 

 

 

 

 

 

 

 

 

 

 

Front

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

panel

3

 

 

 

 

 

(This page)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1Tally Lamps (Red and Green)

Can be lit by a control signal (red tally and green tally) from a GPI/camera.

If the red tally and green tally light at the same time, the tally color will become amber.

2Protective panel mounting screw holes (8 holes)

Eight screw holes have been provided to enable attachment of a permanent protection panel. The screws for the protec- tive panel are installed in the mounting screw holes at time of shipment. To attach a protective panel, first remove the screws before securing the panel.

<Note>

The LCD panel is shipped covered with a packaging material to protect it from damage during unpacking and transporta- tion. Remove the panel before using the monitor.

Rear panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power supply

 

 

 

Rear panel

 

 

 

(→page 12)

(you can switch between AC

 

 

 

 

 

and DC (→page 13))

3Tilt Stand

The tilt stand allows you tilt the unit approx. 10 degrees for- ward or approx. 15 degrees backward.

When tilting the unit, firmly hold the bottom of the stand and move the top of the unit.

If you want to remove the tilt stand, refer to “Detaching and Attaching the Tilt Stand” (→page14).

<Note>

•When tilting the monitor, be careful not to trap your hand between the monitor and stand.

Front panel

HEADPHONES

VIDEO SDI 1

SDI 2

HDMI

DVI-I

1

2

3

4

5

MENU

RETURN

 

 

INPUT SELECT

 

 

 

 

FUNCTION

 

 

 

PICTURE VOLUME

5

 

6

 

1

 

2

POWER switch

Switches the power supply ON/OFF. When the power is ON, the LED (green) lights.

To turn the power off, press and hold the switch for at least three seconds.

INPUT SELECT button

Selects the signal input line. The green LED light above the pressed button indicates the selected input signal.

VIDEO

: Video input

SDI1

: Serial digital interface input (HD/SD compatible)

SDI2

: Serial digital interface input (HD/SD compatible)

HDMI

: HDMI input (HDCP compatible)

DVI-I

: DVI-I input (HDCP compatible)

•Selects one of four input signals: digital video or PC signal, analog video or PC signal. (→page 38)

34

•The input line when the power supply is switched ON is the one that was selected the last time the power was switched OFF.

•When the control lock is on, the mark appears and input lines cannot be changed. (→page 41)

•When INT-SG (internal chart for adjustment “Color Bar + Grayscale”) is selected, all LEDs above the INPUT SE- LECT button are off. Use the “INPUT SELECT” menu to select INT-SG. (→page 18)

FUNCTION button FUNCTION1 to FUNCTION5:

Press to use function assigned to the FUNCTION button with the menu.

•When the control lock is on, the mark appears to indicate that FUNCTION operation is disabled. (→page 41)

11