![](/images/new-backgrounds/1318453/318453143x1.webp)
Others
Cautions for Use
ªAbout condensation
If you turn the Camcorder on when condensation occurs on the head or the tape, condensation Indication [3] (yellow or red) is displayed on the viewfinder or the LCD monitor and the messages [3DEW DETECT] or [3EJECT TAPE] (only when the tape is inserted) appear. If so, follow the procedure below.
1Remove the tape if it is inserted.
≥It takes about 20 seconds to open the cassette holder. This is not a malfunction.
2Leave the Camcorder with the cassette cover closed and the battery attached, to cool or warm it to the ambient temperature.
≥The status indicator blinks for about 1 minute and then the Camcorder automatically turns off. Leave it for about 1.5 to 2 hours.
3Turn the Camcorder on again, set it to the Tape Recording/Playback Mode and then check if the condensation indication
disappears.
Especially in cold areas, moisture may be frozen. If so, it may take more time before the condensation indication disappears.
Watch for condensation even before the condensation indication is displayed.
≥If the indicator of the condensation does not display on the LCD screen and/or EVF and you notice condensation on the lens or the main unit, do not open the cassette cover otherwise condensation may be formed on the heads or
the cassette tape.
When the lens is fogged:
Set the [OFF/ON] switch to [OFF] and leave the Camcorder in this condition for about 1 hour. When the lens temperature becomes close to the ambient temperature, the fogging disappears naturally.
ªAbout dirty heads
If video heads (the parts that closely contact with the tape) become dirty, normal recording and playback are not properly performed.
Clean the heads with the digital video head cleaner.
≥Insert the head cleaner into the Camcorder, set
it to the Tape Playback Mode and play it back for about 10 seconds. (If you do not stop the playback, it automatically stops about
15 seconds later.)
≥We recommend cleaning the heads periodically.
72
If the heads become dirty, “NEED HEAD CLEANING”appearsduringrecording.During playback, moreover, the following symptoms appear.
≥Black or blue
≥The whole screen becomes blue and there is no picture or sound.
When normal playback cannot be performed even after the head cleaning
One possible cause is that normal recording could not be performed because the heads were dirty at the time of recording. Clean the heads and perform recording and playback again. If normal playback can be performed, the heads are clean. Before an important recording, be sure to conduct a test recording to make sure that normal recording can be performed.
≥If the heads become dirty soon after cleaning, the problem may be the tape. If so, try another
cassette.
≥During playback, the picture or sound may be interrupted momentarily, but this is not a malfunction of the Camcorder. (One possible cause is that the playback is interrupted by dirt or dust that momentarily adheres to the heads.)
ªAbout the Camcorder
≥When the Camcorder is used for a long time, the Camcorder body becomes warm, but this is not a malfunction.
Keep the Digital Video Camcorderas faraway as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.).
≥If you use the Digital Video Camcorder on top of or near a TV, the pictures and sound on the Digital Video Camcorder may be disrupted by electromagnetic wave radiation.
≥Do not use the Digital Video Camcorder near cell phones because doing so may result in noise adversely affecting the pictures and sound.
≥Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields created by speakers or large motors.
≥Electromagnetic wave radiation generated by microprocessors may adversely affect the Digital Video Camcorder, disturbing the pictures and sound.
≥If the Digital Video Camcorder is adversely affected by electromagnetic equipment and stops functioning properly, turn the Digital Video Camcorder off and remove the battery or disconnect AC adaptor. Then reinsert the
LSQT1091