Paradyne 3160-A4, 3161, and 3165-A4 - page 247

F. SNMP MIB Objects

3160-A2-GB24-10 March 2001 F-7

Interface Group – “ifSpeed” Object (ifEntry 5)

This object provides the interface’s current bandwidth in bits per second. The

value of this object for each interface is specified as follows:

Interface Group – “ifAdminStatus” Object (ifEntry 7)

This object specifies the desired state (configuration) of the interface. This object

is supported only for the COM and MODEM ports. It provides the ability to switch

between using the port for SNMP or ASCII operations (dial-out, front panel

emulation). The value of this object will not affect the state of any of the interfaces

on the DSU/CSU other than the COM or MODEM port. Only the following values

are supported by the DSU/CSU:

up(1) – The SNMP management link is active on the COM or MODEM port.

testing(3) – The SNMP management link is inactive on the COM or MODEM

port. These ports can be used for proprietary ASCII func tions.

T1 Interfaces: 1,544,000 bps.

COM, AUX, and

MODEM: The currently configured data rate for the port.

Data Ports: The currently configured data rate for the port when the port

is allocated to one of the T1 interfaces. If the port is not

allocated the data rate is defined as zero.

Contents

Main Page Important Safety Instructions C Direct Feed Power Supply Warning WARNING: UNITED STATES EMI NOTICE: CANADA EMI NOTICE: Government Requirements and Equipment Return United States NOTICE TO USERS OF THE UNITED STATES TELEPHONE NETWORK E Canada NOTICE TO USERS OF THE CANADIAN TELEPHONE NETWORK CAUTION: Contents About This Guide 1 Introduction 2 Installation ii 3 Using the Front Panel 4 Configuration 5 Security 6 Using the Integral Modem iv 7 Monitoring and Troubleshooting 8Testing A Front Panel Menu B Technical Specifications C Configuration Options D Configuration Worksheets E Pin Assignments vi F SNMP MIB Objects G IP Network Addressing Scenarios Page Page About This Guide Document Purpose and Intended Audience Document Summary Section Description x Product-Related Documents ACCULINK 3165 DSU/CSU Quick Reference 3165-A2-GL11 3164-A2-GL10 3161-A2-GL11 Reference Documents Page Introduction Features 1-2 DTE Drop/Insert (DSX-1) Interface Alarm Message Capability Front Panel Emulation Integral Modem Async Terminal Interface Support Physical Description Standalone DSU/CSU Front Panel 1. Introduction 1-4 Figure 1-1. 3160 DSU/CSU Front Panel 496-14937 3164 Figure 1-2. 3164 DSU/CSU Front Panel Standalone DSU/CSU Rear Panel 1. Introduction CAUTION: COM MODEM NETWORK POWER PORT 1 1-6 Figure 1-5. 3164 DSU/CSU Rear Panel Figure 1-6. 3165 DSU/CSU Rear Panel 10 BASE-T Table 1-1. Standalone DSU/CSU Rear Panel Connectors Name Function Page Installation ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide Application Examples 2. Installation 2-2 Figure 2-1. Point-to-Point Application Example SERVICES Figure 2-3. Fractional T1 Application Example Figure 2-2. Shared Access Application Example SNMP or Telnet Connection Examples 2-4 Important Instructions Important Safety Instructions HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES Installation Steps Optional Power Sources (Model 3164 Only) 2-6 Optional Power Sources (Model 3164 Only) Installing the +24 Vdc Power Supply Installing the Single 48 Vdc Power Supply 2-8 Installing the Redundant 48 Vdc Power Supply 2. Installation 3160-A2-GB24-10 March 2001 2-9 Cabling Examples T1 NETWORK Figure 2-11. Cabling Examples Pin Assignments Figure 2-11, Cabling Examples, illustrates some cabling examples. Power-On Self- Test xxxxxxxx Self-Test Health Messages Page Using the Front Panel ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide Front Panel Front Panel Emulation 3-2 LCD Device Health and Status Messages Keypad 3-4 Test Jac ks Test Jacks Test in g LEDs Selecting the DTE Drop/Insert or Data Port for LED Display 3-6 Table 3-1. System LEDs Table 3-2. Network Interface LEDs 3-8 Table 3-4. Data Port LEDs 3-10 Displaying Unit Identity 4. The following screens appear in the order listed each time you press the key. 3-12 Selecting the DTE Drop/Insert or Data Port for LED Display Displaying LED Conditions Front Panel Emulation 3-14 Resetting the DSU/CSU Download Operations Page Configuration 4-2 Setting Customer Identification Changing Configuration Options 4-4 Displaying/Editing Configuration Options 4-6 Saving Edit Changes Selecting/Copying to a Specific Port Configuration Options 4-8 from to Configuring the 10BaseT Port (Models 3160 and 3165) 4-10 Setting the 10BaseT Port IP Address Setting the 10BaseT Port Subnet Mask Setting the 10BaseT Port IP Address 4-12 Setting the Default Gateway Address Configuring the COM Port or Modem Port for SNMP or Telnet Access 4-14 Selecting the Port Setting the IP Address xxx.xxx.xxx.xxx 4-16 Selecting the Link Layer Protocol Selecting the Port 4-18 Specifying the Community Name(s) and Access Type(s) 4-20 Configuring SNMP Traps SNMP Traps Enabling SNMP Trap Messages 4-22 Selecting the Number of Trap Managers Configuring a Destination for SNMP Traps Setting the IP Address n 4-24 Configuring DS0 Channels Allocating Data Ports 4. Configuration 3160-A2-GB24-10 March 2001 4-25 Figure 4-1. Example of Channel Allocation 4-26 Figure 4-2. Example of Interface Worksheet for Network Interface Network Interface Network Channel Allocation Figure 4-3. Example of Interface Worksheet for DTE Drop/Insert Interface DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation 4-28 Figure 4-4. Example of RBS Information Worksheet DTE Chan Config Assign: (N1 24) Voice (RBS or Data) Figure 4-5. Port Channel Configuration Worksheet (Ports 1 and 2) Port Chan Conf Options Value 4-30 Figure 4-6. Port Channel Configuration Worksheet (Ports 3 and 4) Conf Options Value Displaying DS0 Channel Assignments 4-32 Allocating Data Ports 4-34 Block or ACAMI Assignment Method 4-36 Individual Channel Assignment Method Allocating DS0 Channels from the DTE Drop/Insert Interface to the Network Interface 4-38 n. Clearing DS0 Channel Allocation 4-40 Providing Backup Capability Selecting the Timing Source Configuring for Network Timing Configuring for External Timing Figure 4-7. Common Clocking Configurations 4-42 Configuring for Network Timing Configuring for External Timing 4-44 Enabling the COM Port for Carrier-Mounted DSU/CSUs COMSPHERE 3000 Series Carrier Installation Manual Page 4-46 Table 4-2. Control Sequence Sequence ASCII HEX Deactivating the Alarm Relay for Carrier-Mounted DSU/CSUs Page Security 5-2 Establishing Access Security on a Port Setting a Password Setting a Password Establishing Access Security on a Port 5-4 Entering a Password to Gain Access Setting a Password Acquiring/Releasing the User Interface Acquiring the Active User Interface User I/F 5-6 Releasing the Active User Interface Enabling/Disabling the Front Panel Page User Interface Access Security for Standalone DSU/CSUs 5-10 Changing User Interface Access Security Using the Integral Modem Using the Integral Modem in Standalone DSU/CSUs User Interface Configuration Options 6-2 Entering Numbers in the Phone Directories Page 6-4 Initiating a Call for Front Panel Pass-Through Operation Configuration Options), Page 6-6 Initiating a Call for PC, ASCII Terminal/Printer, or SNMP Operation Disconnecting the Modem Connection Page Monitoring and Troubleshooting 7-2 Self-Test Health Messages Installation Table 7-1. Self-Test Health Messages xxxxxxxx 7-4 Device Health and Status Messages Table 7-2. Device Health and Status Messages (1 of 2) xxxxxxxx 7-6 Performance Reports Page 7-8 Page 7-10 Table 7-3. Performance Registers (1 of 2) Register Interval Description Totals Description Table 7-3. Performance Registers (2 of 2) Register Interval Description Totals Description 7-12 Ethernet Statistics (Models 3160 and 3165) Alarms Displaying Unit Identity Using the Front Panel 7-14 Alarm Configuration Options SNMP Traps Configuring SNMP Traps Configuring SNMP Traps Page 7-16 Troubleshooting Table 7-7. Troubleshooting (2 of 3) 7-18 Table 7-7. Troubleshooting (3 of 3) Tes ti ng 8-2 Tes t J ac ks Figure 8-3. Test Jack Block Diagram Tabl e 8- 1. Tes t Ja ck F unct io ns Test Jac k Na me Fun cti on 8-4 Test Jack Configuration (Model 3160 and 3164 DSU/CSUs) Test Commands Remote Loopback Tests 8-6 Sending a Line Loopback Up or Down Sending a V.54/ANSI FT1 Activation/Deactivation 8-8 Local Loopback Tests Line Loopback (LLB) 8-10 Payload Loopback (PLB) DTE Loopback (DLB) 8-12 Repeater Loopback (RLB) Data Channel Loopback (DCLB) 8-14 Data Terminal Loopback (DTLB) Aborting Loopbacks 8-16 Tes t P at t er ns Sending Test Patterns 8-18 Monitoring Test Patterns 8-20 Aborting Test Patterns Lamp Test Starting a Lamp Test 8-22 Aborting a Lamp Test Displaying DSU/CSU Test Status Page A 3160-A2-GB24-10 March 2001 A-1 Front Panel Menu Page B Technical Specif i cations B-2 C Configuration Options C-2 DTE Interface Configuration Options Port Configuration Options Table C-1. DTE Interface Configuration Options (2 of 2) Table C-2. Port Configuration Options (1 of 5) C-4 Table C-2. Port Configuration Options (2 of 5) Table C-2. Port Configuration Options (3 of 5) C-6 Table C-2. Port Configuration Options (4 of 5) Table C-2. Port Configuration Options (5 of 5) C-8 Network Interface Configuration Options Table C-3. Network Interface Configuration Options (1 of 3) Table C-3. Network Interface Configuration Options (2 of 3) C-10 Channel Configuration Options Table C-4. DTE Channel Configuration Options n, C-12 Table C-5. Data Port Channel Configuration Options (1 of 4) Configuration Configuring DS0 Channels Table C-5. Data Port Channel Configuration Options (2 of 4) OR C-14 Table C-5. Data Port Channel Configuration Options (3 of 4) OR Table C-5. Data Port Channel Configuration Options (4 of 4) C-16 General Configuration Options Table C-6. General Configuration Options (1 of 2) Table C-6. General Configuration Options (2 of 2) C-18 User Interface Configuration Options Table C-7. User Interface Configuration Options (2 of 11) C-20 Table C-7. User Interface Configuration Options (3 of 11) Table C-7. User Interface Configuration Options (4 of 11) X.X C-22 Table C-7. User Interface Configuration Options (5 of 11) Table C-7. User Interface Configuration Options (6 of 11) C-24 Table C-7. User Interface Configuration Options (7 of 11) Table C-7. User Interface Configuration Options (8 of 11) C-26 Table C-7. User Interface Configuration Options (9 of 11) Table C-7. User Interface Configuration Options (10 of 11) C-28 Table C-7. User Interface Configuration Options (11 of 11) Alarm Configuration Options C-30 Table C-8. Alarm Configuration Options (2 of 4) Table C-8. Alarm Configuration Options (3 of 4) C-32 Table C-8. Alarm Configuration Options (4 of 4) Management Configuration Options C-34 Table C-9. General Management Configuration Options (2 of 7) Table C-9. General Management Configuration Options (3 of 7) C-36 Table C-9. General Management Configuration Options (4 of 7) Table C-9. General Management Configuration Options (5 of 7) C-38 Table C-9. General Management Configuration Options (6 of 7) Table C-9. General Management Configuration Options (7 of 7) C-40 Table C-10. Management Trap Configuration Options (1 of 3) Table C-10. Management Trap Configuration Options (2 of 3) C-42 Table C-10. Management Trap Configuration Options (3 of 3) Page D-2 Page D-4 Prt1 Options Value (Default in Bold) Prt2 Options Value (Default in Bold) D-6 Prt3 Options Value (Default in Bold) Prt4 Options Value (Default in Bold) Network Interface Network Channel Allocation D-8 DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation DTE Chan Config Assign: (N1 24) Voice (RBS or Data) D-10 Conf Options Value (Default in Bold) D-12 Mgmt Trap Options Value (Default in Bold) Page E Pin Assignments Equipment List T1 Network Interface E-2 Figure E-1. T1 Line Interface Cable, RJ48C-to-RJ48C Figure E-2. T1 Line Interface Cable, RJ48C-to-DA15P DTE Drop/Insert Interface DTE Interface Configuration Options E-4 10BaseT Connector MODEM Port Interface E-6 AUX Port Interface (Model 3164 Only) COM Port Interface E-8 Figure E-5. COM Port-to-PC Cable Figure E-6. COM Port-to-Terminal/Printer Cable EIA-530-A Port Interface Connector Mnemonic ITU-T Number Direction Pin E-10 EIA-530-A-to-RS-449 Cable Interface Figure E-7. EIA-530-A-to-RS-449 Adapter Table E-7. RS-449 Cable Interface Signal Circuit Mnemonic ITU-T Number Direction Pin E-12 EIA-530-A-to-V.35 Cable Interface Figure E-8. EIA-530-A-to-V.35 Adapter Table E-8. V.35 Cable Interface Signal ITU-T Number Direction Pin E-14 EIA-530-A-to-X.21 Cable Interface Serial Crossover Cable Figure E-10. Serial Crossover Cable E-16 Power Input Connector Optional DC Power Cable (Model 3164 Only) Installation External Clock Interface Page F SNMP MIB Objects MIB II (RFC 1213) DS1/E1 MIB (RFC 1406) RS-232-like MIB (RFC 1317) MIB II (RFC 1213) System Group, MIB II xxxx-xx-xxx yy.yy.yy zzzz-zzz; Page F-4 Interface Group, MIB II Page F-6 Page F-8 Page F-10 IP Group, MIB II Page F-12 ICMP Group, MIB II TCP Group, MIB II UDP Group, MIB II Transmission Group, MIB II F-14 DS1/E1 MIB (RFC 1406) Near End Group, DS1/E1 MIB Page F-16 Page F-18 Far End Group, DS1/E1 MIB DS1 Fractional Group, DS1/E1 MIB RS-232-like MIB (RFC 1317) F-20 General Port Table, RS-232-like MIB Page F-22 Asynchronous Port Table, RS-232-like MIB Synchronous Port Table, RS-232-like MIB Input Signal Table, RS-232-like MIB F-24 Output Signal Table, RS-232-like MIB Generic-Interface MIB Extensions (RFC 1229) Generic Interface Test Table, Generic Interface MIB F-26 Enterprise MIB F. SNMP MIB Objects F-28 Correlation between Menu Commands and SNMP Objects values for SNMP objects are displayed in italics. Table F-1. SNMP MIB to Front Panel Command Cross-Reference (1 of 3) F-30 Table F-1. SNMP MIB to Front Panel Command Cross-Reference (2 of 3) Table F-1. SNMP MIB to Front Panel Command Cross-Reference (3 of 3) Page G IP Network Addressing Scenarios G-2 Standalone at the Central Site Daisy-Chained Standalones at the Central Site G-4 Local Carrier with Remote Standalone G. IP Network Addressing Scenarios 3160-A2-GB24-10 March 2001 G-5 Local and Remote Carriers Different Subnets Figure G-4. Local Carrier Connected to Remote Carriers G. IP Network Addressing Scenarios G-6 Local and Remote Carriers Same Subnet Figure G-5. Local Carrier Connected to Remote Carriers an Alternative 135.19.6.1 . . . . 135.19.6.16 135.19.20.1 . . . . 135.19.20.16 135.19.1.1 . . . . 135.19.1.16 Multiple NMSs Page H Front Panel Emulation ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide Installing Front Panel Emulation Software H-2 Starting Front Panel Emulation H-4 Displaying LED Conditions Using the Front Panel I Asynchronous Terminal Interface Operation Before Using the ATI Configuring the COM Port or Modem Port for SNMP or Telnet Access I-2 Initiating an ATI Session IP Network Addressing Scenarios Entering a Password to Gain Access Ending an ATI Session I-4 Menu Organization Figure I-2. Menu Organization Main Status Test Configuration Edit/Display Using ATI Screens I-6 NOTES: Setting Customer Identification I-8 Displaying LED Conditions Changing Configuration Options Displaying or Editing Configuration Options I-10 Saving Edit Changes I-12 Establishing Access Security on a Port Setting a Password Setting a Password Establishing Access Security on a Port I-14 Entering a Password to Gain Access If the password is valid If the password is invalid If an invalid password is entered three consecutive times J Equipment List and the Cable numbers for the 3161 DSU/CSU are located in the ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide Page Glossary GL-2 Page GL-4 Page GL-6 Page GL-8 Page GL-10 Index Numerics A B C D E F G I K M N O P Q R S IN-6 T U V W X