Peavey IA 800V, IA 200V, IA Series owner manual IA 400V Specifications

IA™ 400V SPECIFICATIONS

Rated Power (two channels): 200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD

Rated Power (one channel): 215 watts @ 1 kHz at < 0.0075%

THD

Minimum Load Impedance: IA 400V-70: 25 ohms

IA 400V-100: 50 ohms

Maximum RMS Voltage Swing: IA 400V-70: 86 volts

IA 400V-100: 116 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

IA 400V-70:

10 Hz - 100 kHz; +0, -3 dB at rated power

IA 400V-100:

10 Hz - 50 kHz; +0, -.3 dB at rated power

THD (two channels driven): IA 400V-70:

<0.1% @ 200W from 20 Hz - 20 kHz with both channels driven

IA 400V-100:

<0.15% @ 200W from 20 Hz - 20 kHz with both channels driven

THD (one channel driven):

IA 400V-70:

<0.005% @ 200W @ 1 kHz IA 400V-100:

<0.015% @ 200W @ 1 kHz

SMPTE IMD:

< 0.1% 60 Hz and 7 kHz, 200W

Slew Rate:

IA 400V-70: 30V/µs

IA 400V-100: 40V/µs

Damping Factor:

IA 400V-70:

>1,000:1 @ 20 Hz - 400 Hz IA 400V-100:

>2,000:1 @ 20 Hz - 400 Hz

Input CMRR:

> -65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB) standard, x20 (26 dB) internally jumper-selectable

Input Sensitivity:

IA 400V-70:

1.77volts or 3.54 volts for rated output

IA 400V-100:

2.5volts or 5 volts for rated output

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-110 dB, “A” weighted referenced to rated power

Crosstalk:

IA 400V-70:

>-70 dB, “A” weighted referenced to rated power

IA 400V-100:

>-65 dB, “A” weighted referenced to rated power

Current Draw @ 1/8 power: IA 400V-70: 415 watts

IA 400V-100: 385 watts

Current Draw @ 1/3 power: IA 400V-70: 600 watts

IA 400V-100: 565 watts

Idle Current Draw:

IA 400V-70:

38 watts in Standby Mode IA 400V-100:

43 watts in Standby Mode

Maximum Current Draw:

IA 400V-70:

970 watts for rated power IA 400V-100:

840 watts for rated power

Thermal Emissions (BTU/hr.):

IA 400V-70:

1591 watts @ 1/3 power IA 400V-100:

1472 @ 1/3 power

Cooling:

80mm DC fan, off until heatsinks reach 45oC, then variable speed

Controls:

2 rear panel attenuators, sequential turn on/off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power,

4-terminal barrier strip, IEC AC power connector

Construction:

18 ga. steel reinforced with 12 ga. rack ears, extruded aluminum front panel

Dimensions:

3.48" x 19" x 16.4" (15.8" rear mounting ears)

88.4mm x 483mm x 416.6mm (401mm behind rear mounting ears)

Gross Weight: 33.5 lbs. (15.2 kg.)

Net Weight:

31 lbs. (14.06 kg.)

®

TM

Due to our efforts for constant improvements,

features and specifications listed herein are subject to change without notice.

16