Peavey IA Series, IA 800V, IA 200V Caractéristiques IA, Rated Ppwer 1 x 4 ohms, Max. Current Draw

CARACTÉRISTIQUES IA ™ 200

Rated Power (2 x 4 ohms):

150 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD

Rated Power (2 x 8 ohms):

100 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD

Rated Ppwer (1 x 4 ohms):

160 watts @ 1 kHz at < 0.01% THD

Rated Power (1 x 8 ohms):

110 watts @ 1 kHz at < 0.005% THD

Minimum Load Impedance: 4 ohms

Maximum RMS Voltage Swing: 35 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

10 Hz -100 kHz; +0, -3 dB at rated power

THD (2 x 4 ohms):

<0.05% @150W from 20 Hz - 20 kHz with both channels driven

THD (2 x 8 ohms):

<0.05% @ 100W from 20 Hz - 20 kHz with both channels driven

THD (1 x 4 ohms):

< 0.01% @ 170W @ 1 kHz

THD (1 x 8 ohms):

< 0.005% @ 110W @ 1 kHz

SMPTE IMD:

<0.1% 60 Hz and 70 kHz, 150W @

4 ohms

Slew Rate: -25V/µs

Damping Factor (8 ohms):

> 550:1 @ 20 Hz -1 kHz

Input CMRR:

> -65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB) standard, x20 (26 dB) internally jumper-selectable

Input Sensitivity (x40):

.61 volts @ ohms, .71 volts @ 8 ohms

Input Sensitivity (x20):

1.23volts @ 4 ohms, 1.4 volts @ 8 ohms

Input Impedance: 20 k

Hum and Noise:

>-105 dB, “A” weighted referenced to rated power

Crosstalk:

>-75 dB, “A” weighted referenced to rated power @ 8 ohms

Current Draw @ 1/8 power:

330 watts @ 4 ohms, 230 watts @

8 ohms

Current Draw @ 1/3 power:

550 watts @ 4 ohms, 330 watts @

8 ohms

Idle Current Draw:

25 watts in Standby Mode

Max. Current Draw:

800 watts @ 4 ohms, 510 watts @

8 ohms

Thermal Emissions (btu/hr.): 1,364 @ 1/3 power 4 ohms, 443 @ 1/3 power 8 ohms

Cooling:

80mm DC fan, off until heatsinks reach 45o C, then variable speed

Controls:

2 rear panel attenuators, sequential turn on/off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power, 4-terminal barrier strip, IEC AC power connector

Construction:

18 ga. steel reinforced with 12 ga. rack ears, extruded aluminum front panel

Dimensions:

3.48" x 19" x 16.4" (15.8" behind rear mounting ears)

88.4mm x 483mm x 416.6mm (401mm behind rear mounting ears)

Gross Weight:

33 lbs. (15 kg)

Net Weight:

29.6 lbs. (13.4 kg)

TM®

Etant donnés nos efforts constants pour l’amélioration de notre matériel,

les caractéristiques et spécifications listée ici peuvent être modifiées sans préavis.

45