Sequential TURN-ON/TURN-OFF | Peavey IA 800V, IA 200V, IA 400V

SEQUENTIAL TURN-ON/TURN-OFF

The IA Series comes standard with remote sequential turn-on for applications not under computer control. The amplifier front power switch is set to “STANDBY”. An external Direct Plug-In Power Supply Unit providing a nominal voltage between 12 to 24 volts DC must be applied to the rear- mounted

4-pin plugable terminal. The “ENABLE OUT” is connected to the “ENABLE IN” of the next amplifier. IA Series amplifiers are bussed or “daisy-chained” together in parallel and connected to the DC sup- ply by connecting all “24V DC+” terminals together and all “COMMON” terminals together. The first amplifier in the chain requires an SPST closure between its “ENABLE IN” terminal and “24V DC+” terminal to initiate the power turn-on sequence and keep the amplifiers in the chain powered on. This function may be performed under computer control if equipped with an optional module contain- ing sequential capability. If this optional module is used, no connections need be made to the plugable terminal.

SEQUENTIAL TURN-ON/TURN-OFF WIRING

11

Image 11

Peavey IA 800V, IA 200V, IA 400V, IA Series owner manual Sequential TURN-ON/TURN-OFF Wiring

Contents

Series Power Amplifiers Precautions Table of Contents Introduction Amplifier ConfigurationInstallation and Mounting To SET UP the Amplifier for Basic Usage Front Panel Features Back Panel Features Operation Stereo Mode Connection Diagram Parallel Mode Diagram Module Removal Protection Features Signal Ground Connection Sequential TURN-ON/TURN-OFF Sequential TURN-ON/TURN-OFF Wiring AWG Wire Gauge Chart IA 200 Specifications IA 200V Specifications Damping Factor 8 ohms 4501 @ 20 Hz 1 kHz Input Cmrr IA 400 SpecificationsRated Power 1 x 8 ohms 275 watts @ 1 kHz at 0.005% Gross Weight 33.6 lbs .25 kg Net Weight IA 400V Specifications THD 1 X 8 ohms 0.005% @ 425W @ 1 kHz IA 800 SpecificationsRated Power 2 X 8 ohms Gross Weight 51.4 lbs .3 kg Net Weight Minimum Load Impedance IA 800V-70 12.5 ohms IA 800V SpecificationsCurrent Draw @ 1/8 power IA 800V-70 765 watts Current Draw @ 1/3 power IA 800V-70 1,100 watts Important Safety Instructions Desembalaje Configuración DEL AmplificadorConfiguración DEL Amplificador Para LA Utilización Básica IntroducciónPage Características Delpanel Frontal Características Delpanel Posterior Operación Conexiones DEL Módulo DE Entrada Configuración DEL Modo DE Señal Desmontaje DE Módulos Puentes DE Selección DE GananciaConexiones DE Salida DE Altavoces Compartimiento DE Control DE Amplificadores Cortocircuitos Funciones DE ProtecciónLimitador DE Recorte Protección TérmicaPage Tabla DE Calibres DE Cables Especificaciones DEL Amplificador IA Distorsión por intermodulación según norma Smpte Mínima impedancia de carga IA 200V-70 50 WDistorsión armónica total dos canales amplificados Distorsión armónica total un canal amplificado Distorsión armónica total 2 x 8 W Potencia nominal 2 x 4 WPotencia nominal 2 x 8 W Distorsión armónica total 2 x 4 W Peso neto 14,06 kg Consumo máximo de corriente IA A 4 W, 2,83 V a 8 W % a 600 W desde 20 Hz hasta KHz con señal en ambos canales% 60 Hz y 7 kHz, 600 W a 4 W A 4 W, 1,41 V a 8 W Peso neto 20,41 kg Ancho de banda de potencia IADisipación térmica BTU/h IA ¡GUARDE Estas Instrucciones Instrucciones DE Seguridad Importantes ’OUVERTURE Configuration DES AmplificateursInstallation Introduction LED D’ALIMENTATION LED SignalFace Avant Pattes DE Montage EN Rack Sélecteur DE Mise Sous Tension Trois Positions Communications Face Arriere Modules D’ENTREE ET DE CommunicationModule D’ENTRÉE Bornier DE Sortie Utilisation Manipulation D’UN Module Emplacement Pour ModuleCavaliers DE Selection DE Gain Connexions DES HAUT-PARLEURS Protections Connexion DE LA Masse DU SignalLoad Fault Correction Correction DE Faute DE Charge Enlever OU Remplacer UN Module Connexions TURN-ON/TURN-OFF Séquentiel COURT-CIRCUITProtection Tension Continue Sequence TURN-ON/TURN-OFF Table DE Section DES Câbles Max. Current Draw Caractéristiques IARated Ppwer 1 x 4 ohms Slew Rate -25V/µs Damping Factor 8 ohms THD one channel driven IA Minimum Load Impedance IA 200V-70 50 ohmsMaximum RMS Voltage Swing Watts @ 4 ohms, 1,010 watts @ Ohms 05% @ 200W from 20 Hz KHz with both channels driven X40 32 dB standard, x20 26 dB Max Current Draw Indicator LEDsWatts @ 1/3 power IA 472 @ 1/3 power Voltage Gain Cooling Frequency Response Input Impedance Connectors Rated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hrDamping Factor 8 ohms Rated Power 2 x 8 ohms Rated Power 1 x 4 ohms Controls Max Current Draw 15% @ 400W from 20 Hz to KHz with both channels driven IA Important Safety Instructions Auspacken Installation UND MontageSET UP FÜR DEN Einfachen Gebrauch Einführung SCHUTZ-LED Front Panel Features Chassis FÜR DIE RackmontageAC Netzschalter MIT 3 Positionen LED-ANZEIGE Kommunikationsschacht Anschlussfeld Rückseite EINGANGS- UND KOMMUNIKATIONS-MODULEEINGANGS-MODULE LS Anschlussleiste Betrieb Lautsprecher Ausgänge Signal Mode KonfigurationGain Select Jumper Entfernen Oder Austauschen Eines Modules Signal ERDUNGS-VERBINDUNGVerstärker Steuerschacht Modul Entfernen EIN- / Ausschaltfolge Sequentielles EIN- / Ausschalten ÜberhitzungsschutzDC Spannungsschutz Leiter Querschnittstabelle IA 200 Spezifikationen IA 200V Spezifikationen IA 400 Spezifikationen Nettogewicht IA 400V SpezifikationenLeistungsbandbreite Eingangs Cmrr IA 800 Spezifikationen IA 800V Spezifikationen Wichtige Sicherheitsrichtlinien Peavey ONE-YEAR Limited WARRANTY/REMEDY Product of Peavey Electronics Corporation