Peavey IA 200V, IA 800V, IA 400V Rated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hr

CARACTÉRISTIQUES IA ™ 800

Rated Power (2 x 4 ohms):	Slew Rate:	Thermal Emissions (BTU/hr.):
600 watts @ 20 Hz - 20 kHz, both	30V/µs	4,603 @ 1/3 power 4 ohms, 3,012 @
channels driven at < 0.1% THD		1/3 power 8 ohms
	Damping Factor (8 ohms):
Rated Power (2 x 8 ohms):	> 350:1 @ 20 Hz - 1 kHz	Cooling
400 watts @ 20 Hz - 20 kHz, both		120mm DC fan, off until heatsinks
channels driven at < 0.05% THD	Input CMRR:	reach 45° C, then variable speed
	> -65 dB @ 1 kHz
Rated Power (1 x 4 ohms):		Controls:
70 watts @ 1 kHz at < 0.008% THD	Voltage Gain:	2 rear panel attenuators, sequential
	x40 (32 dB) standard, x20 (26 dB)	turn on/off
Rated Power (1 x 8 ohms):	internally jumper-selectable
425 watts @ 1 kHz at < 0.005% THD		Indicator LEDs:
	Input Sensitivity (x40):	2 Clip, 2 Signal, 2 LFC, 1 Protect,
Minimum Load Impedance:	1.22 volts @ 4 ohms, 1.41 volts @ 8	1 Power
4 ohms	ohms
		Protection:
Maximum RMS Voltage Swing:	INPUT SENSITIVITY (X20):	Temp., DC, turn-on bursts, subsonic,
70 volts	2.5 volts @ 4 ohms, 2.83 volts @ 8	incorrect load or short
	ohms
Frequency Response:	Input Impedance:	Connectors:
10 Hz - 25 kHz; +0, -.3 dB at 1 watt	20 k ohms, balanced	8-pin plugable signal input, 4-pin
		plugable sequential power,
Power Bandwidth:	Hum and Noise:	4-terminal barrier strip, IEC AC power
10 Hz - 100 kHz; +0, -3 dB at rated	> -110 dB, “A” weighted referenced to	connector
power	rated power
		Construction:
THD (2 x 4 ohms):	Crosstalk:	18 ga. steel reinforced with 12 ga.
< 0.1% @ 600W from 20 Hz - 20 kHz	> -65 dB, “A” weighted referenced to	rack ears, extruded aluminum front
with both channels driven	rated power	panel
THD (2 x 8 ohms):	Current Draw @ 1/8 power:	Dimensions:
< 0.05% @ 400W from 20 Hz -	950 watts @ 4 ohms, 725 watts @	5.25" x 19" x 16.4" (15.8" behind
20 kHz with both channels driven	8 ohms	rear mounting ears)
		133mm x 483mm x 416.6mm
THD (1 X 4 ohms):	Current Draw @ 1/3 power:	(401mm behind rear mounting ears)
< 0.008% @ 700W @ 1 kHz	1,750 watts @ 4 ohms, 1,150 watts
	@ 8 ohms	Gross Weight:
THD (1 X 8 ohms):		51.4 lbs. (23.3 kg)
< 0.005% @ 425W @ 1 kHz	Idle Current Draw:
	32 watts in Standby Mode	Net Weight:
SMPTE IMD:		45 lbs. (20.41 kg)
< 0.1% 60 Hz and 7 kHz, 600W @	Max. Current Draw:
4 ohms	2,670 watts @ 4 ohms (time limited
	by breaker), 1,725 watts @ 8 ohms

®

TM

Etant donnés nos efforts constants pour l’amélioration de notre matériel,

les caractéristiques et spécifications listée ici peuvent être modifiées sans préavis.

49