Charging the ProntoPro NG | Philips TSU 7500 instruction

Before You Start

4Plug the cable of the battery pack in the connector.

EN

5Slide the battery cover back on.

Make sure the wires of the battery pack do not get stuck while sliding the cover on.

After a few seconds, the ProntoPro NG starts up automatically and an introduction screen appears. The ProntoPro NG beeps twice to indicate that it has finished starting up.

Because the battery pack is not fully pre-charged, you need to charge it as described below.

Charging the ProntoPro NG

For charging the ProntoPro NG, you have to place it in the docking station. When the battery pack is running low, the Low Battery icon will appear on the ProntoPro NG.

You can charge the ProntoPro NG at any time; the battery pack does not have to be entirely empty before recharging.

Note You can continue using the ProntoPro NG while it is being charged.

When the battery pack is empty, the ProntoPro NG’s settings are retained. You only need to set the clock. However, you should recharge the ProntoPro NG as soon as possible to ensure perfect performance.

User Guide

11

Image 11

Philips TSU 7500 manual Charging the ProntoPro NG

Contents

ProntoPro Next Generation User Guide ProntoPro Next Generation Table of Contents Table of Contents ProntoPro NG Home Theater Control Panel Taking a First Look Device Taking a First Look USB port Touch Screen Docking Station ProntoPro NG has a USB port to make downloading much easier What’s New for ProntoPro Next Generation? Before You Start Installing the Battery Pack Charging the ProntoPro NG Cool down the battery pack Turning on ProntoPro NG Tilt ProntoPro NG more than 50 degrees default settingGetting Started Changing the Time Setting Time and DateChanging the Time Format Tools Menu Changing the DateTo change the day To change the month You can change the language used on your ProntoPro NG Setting the LanguageTo change the year Device Overview Operating ProntoPro NG Overview Using the Tools Selecting the Brand and Code Set for your Device Customizing ProntoPro NGDefining the Brand for a Device Tap ‘Code sets’ screen appears Installing the brandSelecting the brand Selecting the code set Tap and point ProntoPro NG at the device Searching the code setSearching the Brand and Code Set for your device Searching the brand Learning Commands Tap the button you want to learn Learning a ButtonLearning a Device Action Tap the Device for which you want to learn a Device Action Labeling Elements You can choose from four different character sets Labeling a Button Follow the instructions 6 to 8 of ‘Labeling a Button’ on Labeling a DeviceLabeling a Tap in the ‘Label Tool’ screen. The Page Overview appears Adding a New Device Adding Devices Copying an Existing Device Delete Tool allows you to delete a button or a device Deleting ElementsDeleting a Button Deleting a Device Moving Devices Adjusting the Settings Select First Settings Page appears Setting the Brightness of the BacklightSetting the Timeout of the LCD Screen Setting the Volume Level of the Touch Screen Setting the Volume LevelSetting the Navigation for ProntoPro NG Setting the Volume Level of the Hard Buttons Calibrating the Touch Screen Setting the Animation Mode Adjusting the Firm Keys Settings Adjusting the Screen Activation Settings Adjusting the Pickup Sensor Settings Adjusting the Cursor Keys Settings Creating a Macro Using the Power FeaturesCreating and Editing Macros To test the macro To add a delay to the action listTo add an action to the action list To add a beep to the action list Deleting an action from the action list Editing a MacroTo finish the macro Moving an action in the action list Activating Timers Creating and Editing Timers Deleting a Timer Creating and Editing TimersAdding a Timer Labeling a Timer Editing a Timer Setting the Start Time or Stop Time Setting the Start Date Defining the Start Action or Stop Action Defining the Repeat Settings Repeat toggle NG’s touch screen Operating ProntoPro NG with the CursorIs provided below the button To set the cursor navigation An RF Extender not included is therefore required Operating ProntoPro NG with RF Selecting RF to Operate your Devices Selecting IR to Operate your Devices Plug one end of the cable in the USB port on your computer With ProntoProEdit NG you can ProntoProEdit NG How do I calibrate the touch screen? Why don’t my buttons work properly?How do I reset ProntoPro NG? Reset button ProntoPro NG shuts off automatically TroubleshootingGeneral Problems Devices do not respond to commands from ProntoPro NG Configuration file is corrupted Customizing ProblemsButtons are not sending the correct commands ProntoPro NG will not learn commands Connection to the PC Memory Storage ProblemsProntoPro NG error messages Timers do not work Upgrading ProntoPro NG Cleaning ProntoPro NGMaintaining ProntoPro NG Important Notices List of Symbols List of Symbols List of Symbols Included Specifications Action Glossary LCD USB Index LCD screen timeout, 33 Learn Tool, 23 learning Volume mute, 5 volume down, 5 volume level, 34 volume up