Basic Playback
Listening in LOUDNESS Mode
The LOUDNESS mode allows you to boost the bass in a signal. It is useful for listening to music at low volumes.
|
| MAIN | |
Receiver | MAIN SUB | ||
| DSP | STEREO | |
| / dts | EFFECT | |
THX | ADVANCED | STANDARD | |
THEATER | |||
|
| ||
MIDNIGHT |
| MULTI CH | |
| IN | ||
|
| ||
DIGITAL | LOUDNESS | SIGNAL | |
NR | SELECT |
LOUDNESS
LOUDNESS
Press the LOUDNESS button on the remote control’s Receiver MAIN screen or on the front panel.
Each press switches LOUDNESS mode on or off.
memo • You can’t use the LOUDNESS mode with the MULTI CH IN or THX modes.
•If you press LOUDNESS in DIRECT mode the receiver will switch to STEREO mode.
Adjusting Bass and Treble (Tone Control)
You can use BASS +/– or TREBLE +/– buttons to adjust the low and high frequencies for each individual set of speakers. If the receiver is in STEREO mode you can only adjust the FRONT speakers. In a surround mode (STANDARD, ADVANCED THEATER, etc.) you can adjust the FRONT, CENTER, SURROUND and SURROUND BACK speakers. The TONE button can also be used to bypass the tone circuitry (See p.22).
| 3 |
|
|
|
| SUB | 3 | 1 | Press the TONE button on the | ||||||||||
|
|
|
|
|
| remote control's Receiver SUB | |||||||||||||
Receiver |
|
|
|
|
|
| MAIN |
|
|
|
|
|
|
|
| screen or front panel to put the | |||
|
|
|
|
|
|
| SUB |
|
|
|
|
| |||||||
TAPE 2 | FL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| receiver in tone adjust mode. |
MONITOR | DIMMER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TONE: ON should appear in the display. If TONE: |
|
| BASS |
| TREBLE |
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| BYPASS appears, press the button again to get | ||||||||
INPUT | SPEAKER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
ATT. | A/B |
|
|
|
|
|
|
|
|
| CH |
|
|
|
|
| TONE:ON the tone adjust mode. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
| TONE |
|
|
|
|
|
|
| |||||||
|
|
|
|
| SELECT | 2 |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| LEVEL | SETUP | 2 | Press the CH SELECT button on the | |
| CH | SYSTEM |
|
|
|
| 1 |
|
| remote control or CHANNEL | |
|
|
| SELECT button on the front panel to | ||
TONE | CHANNEL SELECT |
| cycle through the different tone | ||
| adjust channels. |
| |||
|
|
|
|
| |
|
|
|
| The button cycles though the possibilities in the | |
|
|
|
| following order: |
|
|
|
|
| TONE Front | TONE Center |
BASS | TREBLE |
| TONE SurBack | TONE Surr. | |
|
|
|
OPERATION
memo
•The tone control can be adjusted in a range of ±6 dB.
•The tone control cannot be adjusted in THX,
MULTI CH IN.
•If the receiver is in DIRECT mode and you press the TONE button, TONE BYPASS will appear in the display, letting you know that you can't change the tone in DIRECT mode. Another press cancels DIRECT mode.
3Use the BASS or TREBLE
frequencies of each channel.
Display when using the TONE +/- buttons.
A few seconds after you finish adjusting the tone the receiver will revert to the sound mode it was in at the 51 beginning of the process.