Pioneer VSX-AX5Ai-S Controlling other equipment, Programming signals from other remote controls

Controlling other equipment 08

8Repeat steps 3 – 7 for any other components you want to control.

9 When you’re finished, use (cursor up/down) to select ‘*Exit*’ from the menu and press ENTER.

Programming signals from other remote controls

If the preset code for your component is not available, or the available preset codes do not operate correctly, you can program signals from the remote control of another component. This can also be used to program additional operations (buttons not covered in the presets) after assigning a preset code in Recalling preset codes on page 58.

ENTER

DVD/LD	TV/SAT	VCR1 /	TVCONT
		DVR
MULTI CONTROL
VCR2	VIDEO	CD
CD-R/	MD/
TAPE1	TAPE2

REMOTE

SETUP

1Press and hold REMOTE SETUP for three seconds. The REMOTE SETUP menu appears on the remote control display.

2 Use (cursor up/down) to select ‘Learning’ from the menu and press ENTER.

Select Function flashes in the display.

3Press the MULTI CONTROL button that matches the connection for the component you want to control.

For example, press DVD/LD if you want to program an operation for the DVD player that you connected to the DVD/LD terminals.

Select Key flashes in the display.

• You can’t assign the RECEIVER or TUNER buttons.

4Select the button corresponding to the command you want to teach the remote control.

For example, press if you want to program the play command from your DVD player remote control.

LEARN flashes in the display.

•When programming TV CONT, you can only select TV , or one of the TV CONTROL buttons.

5Point the two remote controls towards each other then press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver’s remote control.

For example, if you want to learn the playback control

signal, press .

•The remote controls should be 5–20cm apart, and the LEARN icon should be flashing to indicate the remote is ready to accept a signal.

5 – 20cm

4	8		+
3	7
2	6	0	+
1	5	9	+

If the operation has been learned, the display will show OK

If the operation hasn’t been learned the display will show NG.

Continue? shows in the display (if Select Key is flashing, go back to step 4). Go to step 6.

•If the remote display shows FULL, it means the memory is full. See Clearing remote control settings on page 69 to erase a programmed button you’re not using to free up more memory.

•If NG keeps showing in the display, or the remote control keeps on returning to step 4 (Select Key flashes in the display), it may be possible that the command cannot be learned by this remote control.

Certain buttons represent operations that cannot be learned from other remote controls. The buttons avail- able are shown below:

	DIMMER	LOUDNESS	TONE	EFFECT/CHSEL
	1	2	3	4
	SIGNAL SEL	DNR	BASS/TREBLE	+
	5	6	7	8
	VIDEO SEL	HI-BIT	+10	DISC
	9	0		ENTER
	SYSTEM SETUP		DIRECTACCESS SEARCHMODE
				GUIDE
	MENU			TOPMENU
	TUNER EDIT			TRACK
		ENTER
				EXIT
	AUDIO			RETURN
	MPX	TEXTON RFATT		DISPMODE
				SUBTITLE
	TUNING	BAND		TUNING +
SOURCE	TV			STATION +
	STATION	TEXTOFF CLASS
	CHANNEL			CHANNEL+

6 Use (cursor up/down) to select ‘Yes’ to program additional signals for the current compo- nent.

Repeat steps 4 and 5.

•To program signals for another component, select No and repeat steps 2 through 5.

7 When you’re finished, use (cursor up/down) to select ‘*Exit*’ from the menu and press ENTER. You will return to the REMOTE SETUP menu. Select *Exit* again to exit.

59

En