Pioneer VSX-D909S Switching Analog and Digital Signal Input, source component, Basic Playback

Models: VSX-D909S

1 92
Download 92 pages 4.99 Kb
Page 47
Image 47
Switching Analog and Digital Signal Input

Basic Playback

Switching Analog and Digital Signal Input

This switch moves the input fed to the receiver between analog and digital sources. You need to take special care to switch to the appropriate input, when necessary. For example, the switch would have to be on DIGITAL to use DOLBY DIGITAL or DTS surround sound but it would have to be on ANALOG to record to the analog out jacks on the receiver. The default setting is AUTO (priority is given to a digital signal, if there is one).

S0URCE

USE

RECEIVER

1

1

Put the remote control slide switch in USE.

ë￿

SETUP

 

 

 

MULTI

SYSTEM

 

 

 

 

OPERATION

OFF

 

 

 

 

DVD/LD TV/SAT VCR1 VCR2

 

MULTI CONTROL

 

CD

MD/

TUNER

TVCONT

TAPE1

 

 

 

CLASS

MPX

BAND

DIRECT ACCESS

¦￿

7

3

8

- TUNING +

- STATION +

1 Á￿ 4 ¢

DTV ON/OFF

DTV MENU

- CHANNEL +

1

2

 

3

4

5

 

6

7

8

 

9

GUIDE

0

 

EXIT

 

 

ENTER

+10

 

 

DISC

2Press the SIGNAL SELECT button to select the input signal corresponding to the

source component.

Each press switches the signal in the order below:

3 While SIGNAL SELECT is set to DIGITAL, AC-3 AUTO lights when a Dolby Digital signal is input, ANALOG

DIGITAL

+

TV

+

3 While SIGNAL SELECT is set to DIGITAL, AC-3

TV VOL

TV CONTROL

VOLUME

TV FUNC

lights when a Dolby Digital signal is input,

 

 

 

REMOTE SETUP

 

 

DTS lights when a DTS signal is input.

SYSTEM SETUP

 

 

INPUT

MENU

MUTE

 

ATT

 

 

 

EFFECT/

+

FUNCTION

 

CH SEL

 

 

 

ENTER

 

2

DIGITAL

 

SIGNAL

NR

 

SELECT

MIDNIGHT

MULTI CH

DSP

STEREO/

When a Dolby Digital

LIGHT

INPUT

ADVANCED

DIRECT

signal is input.

 

STANDARD

 

 

 

/DTS

 

AV PRE-PROGRAMMED AND LEARNING

REMOTE CONTROL UNIT

When a DTS signal is input.

2

VSX-D909SDigital Signal Processor

DOWN

UP

memo

In the AUTO setting, SIGNAL SELECT chooses the signal in the following order: DIGITAL, ANALOG.

If the Digital-In Select (see page 31) choices are set to OFF, the SIGNAL SELECT will default to ANALOG.

Because the audio from a karaoke microphone and LD recorded with analog audio only is not output from the digital output, set SIGNAL SELECT to ANALOG.

This receiver can only playback Dolby Digital, PCM (32kHz, 44kHz, 48kHz, and 96kHz), and DTS digital signal formats. If you have some equipment that outputs digital audio in a format other than these you'll have to connect and playback via the receiver's analog inputs (make sure that SIGNAL SELECT is set to ANALOG).

When an LD or CD with DTS is played back with the SIGNAL SELECT set in ANALOG, digital noise caused by playing back the DTS directly (with no decoding) is output. To prevent noise, you need to make digital connections (See pages 13 and 14) and set SIGNAL SELECT to DIGITAL or AUTO.

Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.

OPERATION

47

Page 47
Image 47
Pioneer VSX-D909S Switching Analog and Digital Signal Input, lights when a Dolby Digital signal is input, source component