Techno Tidbits &
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
Symptom |
| Cause |
| Remedy | ||
The power does not turn ON. | • | The power plug is disconnected. | • | Connect the power plug to the wall | ||
|
|
|
|
|
| outlet. |
| • | The protection circuit may have | • | Disconnect the power plug from the | ||
|
| been activated. |
| outlet, and insert again. | ||
The unit does not respond when | • | Static electricity caused by dry air. | • | Disconnect the power plug from the | ||
the buttons are pressed. |
|
|
|
|
| outlet, and insert again. |
No sound is output when a | • Improper connections. | • Make sure the component is | ||||
function is selected. |
|
|
|
|
| connected correctly (see |
| • Sound is muted. | • Press MUTE on the remote control. | ||||
| • The volume is turned down. | • Adjust MASTER VOLUME. | ||||
| • The TAPE 2 MONITOR is ON. | • Press the TAPE 2 MONITOR button. | ||||
| • | Speakers are turned OFF. | • | Press SPEAKERS (A/B) to select the | ||
|
|
|
|
|
| speakers you connected. |
| • DIGITAL/ANALOG switch is set | • Set SIGNAL SELECT (see p.47). | ||||
|
| incorrectly. |
|
| ||
|
|
|
|
| ||
No image is output when a | • Improper connections. | • Make sure the component is | ||||
function is selected. |
|
|
|
|
| connected correctly (see |
| • | The input source is not properly | • | Press the correct function button. | ||
|
| selected. |
|
| ||
Considerable noise in radio | • | Incorrect frequency. | • | Tune in the correct frequency. | ||
broadcasts. | • | The antenna is not connected. | • | Connect the antenna (see p.18). | ||
| • | Digital cable is near the antenna | • | Route digital cable away from the | ||
|
| terminals and wires. |
| antenna terminals and wires. | ||
| FM broadcasts |
|
|
|
| |
|
|
|
|
| ||
| • | The FM antenna is not fully | • | Fully extend the FM wire antenna, | ||
|
| extended or is poorly positioned. |
| position for best reception, and | ||
|
|
|
|
|
| secure to a wall. |
| • | Weak radio signals. | • | Connect an outdoor FM antenna (see | ||
| AM broadcasts |
|
| p.18). | ||
|
|
|
| |||
|
|
|
| |||
| • | The AM antenna is poorly | • | Adjust the direction and position for | ||
|
| positioned. |
| best reception. | ||
| • | Weak radio signals. | • | Connect an additional internal or | ||
|
|
|
|
|
| external AM antenna (see p.18). |
| • | Interference caused by other | • | Turn off the equipment causing the | ||
|
| equipment (fluorescent lamp, |
| noise or move it away from the | ||
|
| motor, etc.). |
| receiver. | ||
|
|
|
|
| • | Place the antenna farther away from |
|
|
|
|
|
| the equipment causing the noise. |
|
|
|
|
| ||
Broadcast stations cannot be | • | Weak radio signals. | • | Connect an outdoor antenna (see | ||
selected automatically. |
|
|
|
|
| p.18). |
|
|
|
|
| ||
Subwoofer output is very low. | • | Settings route signal away from | • | To get more signal to the subwoofer | ||
|
| subwoofer. |
| set it to PLUS or choose SMALL for | ||
|
|
|
|
|
| the FRONT speakers (see |
|
|
|
| |||
When playing a Dolby Digital / DTS | • | The Dolby Digital / DTS source is | • There is no problem with the receiver | |||
source the 5.1 Channel indicator |
| not 5 channels. |
| but if you want 5 channel sound you | ||
doesn't light. |
|
|
|
|
| must play a 5 channel source. |
|
|
|
|
|
|
|
85
