Adjusting Bass and Treble | Pioneer VSX-D909S manual

Basic Playback

Adjusting Bass and Treble

You can use BASS +/– or TREBLE +/– buttons to adjust the low and high frequencies for each individual set of speakers. If the receiver is in STEREO mode you can only adjust the FRONT speakers. In a surround mode (STANDARD, ADVANCED THEATER, etc.) you can adjust the FRONT, CENTER, SURROUND and SURROUND BACK speakers. The TONE button can also be used to bypass the tone circuitry (see p.22).

1 2

VSX-D909SDigital Signal Processor

DOWN

UP

3

1Press the TONE button on the front panel to put the receiver in tone on mode.

2Press the CHANNEL SELECT button on the

front panel to cycle through the different tone adjust modes.

The button cycles though the possibilities in the following order:

TONE Front TONE Center

TONE SurBack TONE Surr.

3Use the BASS or TREBLE (+/–) buttons to adjust the low or high frequencies of each channel.

A few seconds after you finish adjusting the tone the receiver will revert to the sound mode it was in at the beginning of the process.

memo • The tone control can be adjusted in a range of ±6 dB.

•The tone control cannot be adjusted in MULTI CH IN mode.

•If the receiver is in DIRECT mode and you press the TONE button, TONE BYPASS will appear in the display, letting you know that you can't change the tone in DIRECT mode. Another press cancels DIRECT mode.

50

Image 50

Pioneer VSX-D909S manual Adjusting Bass and Treble

Contents

VSX-D909S For Canadian model For U.S. modelImportant Notice Information to User Important Safety Instructions Coaxial Digital Connection Quick Start GuideHooking Up Your DVD Player & TV Optical Digital Connection Setting up the Remote Control & Unit Speaker Connections You should see the following display on your TV Use the 2 or 3 buttons to choose the DVD/LD settingDigital Input Assignment You should see DVD/LD in the display on the receiver Playing a DVD with Surround SoundFor Better Surround Sound For more information see pages Features Table of Contents Preparing the Remote Control Checking the Supplied AccessoriesHow to Use This Manual Before You Start Opening the Front Panel Installing the ReceiverOperating range of remote control unit Audio Components Connecting Your EquipmentCassette deck placement Analog audio/video cords Digital Connections Coaxial cords/Optical cables Memo Example Connection for a DVD/LD or LD playerDigital Input Assignment Video Components Connecting DVD/LD playersConnecting VCRs or DVRs DVD/LD player Or standard video cord Satellite TV ComponentsDigital audio coaxial cords Optical cables TV/Satellite tuner 5.1 channel analog output jack Multi Channel Input External DecoderComponents equipped with FM wire antenna AM loop antenna Connecting the Radio AntennasUsing external antennas Connect an external FM antenna Speakers Speaker terminals Speaker impedance Speaker placementPlacing Your Speakers First turn the receiver off, then press the STANDBY/ON Connecting Additional Amplifiers Plugging Displays & Controls Front Panel Channel Select button Multi CH Input See p.40Tone control buttons Tone button Bass -/+ button See p.50 Station -/+ Use to choose programmed radio stations Adjusts the overall receiver volumeTuner Control buttons See p.54-57 Display Remote Control Remote Setup button when Setup mode is selected Master Volume buttonsInput ATT button when USE mode is selected System SET UP button when Setup mode is selected Initial Set Up On Screen Display Press the System Setup button Setting Up for Surround SoundSet the slide switch to Setup Speaker Setting See p.32-33 Go on to the next page to continue set up Digital in Select should be selected if it Return to the System Setup MenuDigital-In Select Isnt use the 5´ buttons to select it Select Small to send bass frequencies to the subwoofer Speaker Setting´ buttons then press the Enter button Menu Setup Menu Select a Test Tone mode Channel Level Previous screen When you have adjusted each speaker levelPress Enter button to return to Select Exit with the 5/ buttons and press Select Crossover Network if Select Exit to return to the System Setup MenuCrossover Network Continuing from Channel LEVEL, it will This completes the speaker setup Bass Peak Level Dynamic Range Control Default setting is OFFIf listening at loud volumes we recommend turning Use the 2 or 3 arrows to choose OFF, MID or MAX Channel Standard modes Basic PlaybackSound Modes Advanced Theater modes Musical Stereo mode DSP modes Selecting a Sound Mode CH SEL Playing Sources with Dolby Digital or DTS Sound Turn on the power of the playbackPut the remote control slide switch in USE Component Playing Stereo Sources DTS lights when a DTS signal is input Switching Analog and Digital Signal InputLights when a Dolby Digital signal is input Each press switches the signal in the order below Digital input Each press switches Digital NR on or offReducing Noise During Playback AM/FM tuner Each press switches Midnight Listening mode on or off Listening in Midnight ModeListening the Loudness Mode Press the Midnight button Adjusting Bass and Treble Multi Channel in Playback KHz 24 bit Performance Press the FL Dimmer button Adjusting the Brightness of the DisplayDirect Playback Dual Mono Setting For Automatic Tuning Using the TunerAutomatic and Manual Tuning For Manual Tuning Example Direct Access TuningTo cancel before inputting the frequency Press the Memory button to activate the memory function Memorizing Frequently Used StationsTune in the desired station Press the Class button repeatedly to select a class number Recalling Memorized Stations Using the remote controlUsing the front panel Use the Number buttons to select the channel you want Setup Remote Control of Other ComponentsSetting Up the Remote Control to Control Other Components Press the 2´3 buttons to choose Press the Multi Control button forComponent you want to control Function and then press the 5´ buttons Remote SET UP menu appears on your TV screen Learning Commands from Other Remote ControlsPress the Remote Setup button Also make sure that your TV is on and set to the receiver Press the button to be programmed Inches 20 cm Enter Side A/B Using the Remote Control with Other ComponentsSource = Menu Enter TV/VCR VCR & DVD Recorder OperationsChannel -/+ Press to start recording CD-R only CD & CD-R Player OperationsDisc MD Operations Disc DISP/CHARA Exit STB satellite tuner OperationsGuide ÷Á DTV ON/OFF/DTV Menu Disc CH EnterYellow Press to fast forward the tape Cassette Deck OperationsPress to rewind the tape Using Other Functions Recording from Audio Components Recording from Digital Audio Components Recording from Video Components Select a Multi Control button for this To cancel here, press Remote SetupMulti Operations Multi Operation Performing Multi Operations You can repeat this process for up to five commandsRemote sends the Multi Operation commands you pro- grammed Multi Control buttons start to blink System Off Select a component by pressing its Multi Control button Setting Up the Direct FunctionUsing the System Off Button Resetting the Remote Control Remote Back Light Erasing Learned Remote Control Commands Erasing All Learned Commands and Preset Codes Video Select MULTI-ROOM connections Set up exampleMulti-Room Sub room Main room Select the Volume Level by using the 2´3 buttons MULTI-ROOM set upPress System Setup on the remote control Also make sure that the TV is on and set to the receiver Selector Press the Control buttonWithin ten seconds of , select the Function with the Input Press a Function button to select the sub function Using the remote control with the MULTI-ROOM systemPress Volume +/- to adjust the volume Receiver from the sub room Pioneer SR System Operating other Pioneer components Laser disc format Techno Tidbits & Problem-solvingDolby Digital Comparison with Dolby Pro Logic Surround Device Preset Code ListDevice Manufacturer Code Troubleshooting Symptom Cause Remedy Analog DTS Power cord Caution Maintenance of External Surfaces Specifications Page Page 0 4 2 1 1 4 0