Manuals / Pitco Frialator / Kitchen Appliance / Fryer

Pitco Frialator L22-355 Electrical Connections at LEFT and RIGHT connectors, J1Left, Inputs, Type

Models: L22-355

1 28

Download 28 pages 37.69 Kb

Page 26

Image 26

8Electrical Connections at LEFT and RIGHT connectors):

Spin Fryer I12 Cooking Computer

Pitco P/N 60149505

8Electrical Connections at LEFT and RIGHT connectors):

As viewed from the rear of the control.

J1(Left)	Inputs	Type	Nominal	Notes:

1	ACH	PWR	24VAC	24VAC +20% -15% 50/60Hz.
2	ACN	PWR	24VACN	24VAC Return.
3	PROBE+	Thermistor	Resistance varies with vat temperature. 942 Ohms
4	PROBE-	Proble	@ 350°F
5	DVI	IN	24VAC	Drain Valve Interlock
6	HFB	IN	24VAC	Heat Feed Back
7	24VDC COM	IN	24VDC	DC Returm
8	HD	OUT	24VDC	Heat Demand
9	SO/xFER	OUT	24VDC	Side ON or XFER
10	RBL	OUT	24VDC	Right Basket Lift
11	LBL	OUT	24VDC	Left Basket Lift
12	AC2	PWR	24VAC	Aux Power Input

Tip: Use the diagnostic menu to verify operation of outputs, and inputs.

L22-280 Rev 1

Page 26 of 28

Page 26

Image 26

Pitco Frialator L22-355 service manual Electrical Connections at LEFT and RIGHT connectors, J1Left, Inputs, Type, Nominal

Contents

English for Pitco P/N 60149505 Spin FryerI12 Cooking Computer 4 To Enter Programming Level 3 for the Technician 2 To Enter Programming Level 1 for the Store Manager3 To Change Options Level 2 for the Store Manager Probe Resistance Chart Mechanical DimensionsElectrical Connections at LEFT and RIGHT connectors 5 Factory Menu Level 4 for the Technician1.3 To start a cook 1.1 To turn the appliance ON1.2 To turn the appliance OFF 1 Key Locations and FunctionsDefault value is 350, or inactive 1.4 To cancel a cook1.5 To check Actual and Set temperatures 1.7.2 Manual Boil Entry 1.7 To perform a Boil Out operation1.7.1 Automatic Boil Entry Water Detection 2.1 To Set Cook Temperature 2 To Enter Programming Level 1 for the Store Manager2.2.3 Hold Time 2.2.1 Cook Time2.2.2 Shake Time  With display showing2.2.6 Spin Rate 2.2.4 Hold Pre-Alarm2.2.5 Spin Time 2.3 To Exit Level 1 programming3.1 Fahrenheit or Celsius Display 3.2 Password Change or Required?3 To Change Options Level 2 for the Store Manager  If NO PASS is selected Display returns to3.5 Melt Cycle Type Beeper ON/OFF3.4 Language Selection 3.6 Recovery Test Value 4.2 Melt Cycle ON Time 4.1 Offset the Temperature Display4 To Enter Programming Level 3 for the Technician 4.4 Recovery Times 4.3 Minimum ON and OFF Cycle Timeindicator shows the ON or OFF state of the input 4.5 Diagnostic Menu EntryDrain Switch Input All display indicators will be forced on. The purpose is4.6 Ready Level 4.7 Temperature Operating Range4.8 More Service Menu Entry 4.8.1 Instant On Toggle4.8.5 Cancel Duration 4.8.3 Shake Alarm Duration4.8.4 Hold Alarm Duration 4.8.6 Configuration Value4.8.9 Set Network Address 4.8.7 Factory Reset4.8.8 Standing Pilot Toggle 4.9 To Exit Programming LevelThis menu is identical to Offset Temperature Display section Note Do not change this setting. Factory shipped default is OFF5.2 Offset Temperature Display is displayed instead of SERVICEdisplayed instead of SERVICE 5.5 Recovery Test Values5.6 Diagnostic Menu Entry 5.8 Operating Temperature RangeCook Position Indicator 5.10 Spin DiagnosticsActivates the indicator light to show the door’s current Activates the indicator light to show the basket lift’s5.12.1 5.11 Test On/Off5.12 More Factory Menu Entry Control ID Display6 Other Displays Page 24 of Spin Fryer I12 Cooking Computer Pitco P/NL22-280 Rev L22-280 Rev 7 Mechanical DimensionsSpin Fryer I12 Cooking Computer Pitco P/N 25 ofInputs 8 Electrical Connections at LEFT and RIGHT connectorsJ1Left TypeProbe 9 Probe Resistance ChartProbe Resistance in 5F Increments ResistanceSHIPPING ADDRESS - 10 FERRY ST., CONCORD, NH

8Electrical Connections at LEFT and RIGHT connectors):

J1(Left)

Inputs

Type

Nominal