Connection of Control Cable | Planar PS5580 manual

3.6. Connection of Control Cable

•Control signal transmission can be connected by 3 different methods.(RS-232C or Ethernet or IR)

•RS-232C and Ethernet connection cannot be used simultaneously.

•All control signals are output to the RS-232OUT after conversion to RS-232C signal.

3.6.1. Connection of RS-232C Cable & IR Receiver

•Maximum use of RS-232C with Daisy Chain connection is 30 sets or less, if you need additional connection, use RS-232C distributor.

LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT
LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT
LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT
IR Receiver
Max. Distance : 7M
			RS-232C
20˚		20˚

3.6.2. Connection of Ethernet Cable

•In case of Ethernet connection, the control PC should be connected to one of PS5580 sets with Ethernet cable. For the connection between the PS5580 sets, they should be connected with RS-232C cables.

IR Receiver

LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT
LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT
LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT	LAN	IR	RS232C IN	RS232C OUT
LAN Cable	LAN Cable (Cross Cable)
(Direct Cable)	LAN Cable (Cross Cable)
(Direct Cable)

POWER

HUB or Router

(Wireless & Cable)

Ethernet control PC

1	2	3
4	5	6
7	8	9
	0

OK	RS-232C control PC

RS232

LAN

LAN Cable

(Direct Cable)

- 26 -

- 27 -

Image 15

Planar PS5580 user manual Connection of Control Cable

Contents

User’s Manual Supplied Accessories Contents It is recommended to install the set with good ventilation Do not install the set at the air-tight condition ※Clearance for Ventilation ※Please keep following PS5580 It always needs two persons to carry or installWhen you carry PS5580 with up straight Panel when you put down the panel ※Attention for Installing Safety Precautions Display control via COM port D-Sub 9pin Remote controller input portNames Display control via Ethernet RJ45 KEY PAD Connection of Single PS5580 How to Connect Cables Connection of Multiple PS5580 for DP Resolution Output Port Connection Remark Connection of Multiple PS5580for DVI Connection of Control Cable How to use Remote Controller Configuration Sharpness BrightnessContrast Back Light Color Temperature TintColor Select Color Balance from Picture Menu Adjust Color BalanceColor Balance Gamma Selection Color Space Picture Reset Select V Position from Screen menu PositionSelect H Position from Screen menu Select Screen Menu Clock Screen Reset Select Auto Adjust from Setup a menu Select Setup a Menu‚ Each of the value can be adjusted by pressing buttons Select Auto Power from Setup a menu Power SaveAuto Power Select Power Save from Setup a menu Language Setup a ResetSelect Language from Setup a menu Select Setup a Reset from Setup a menu KEY Lock Select KEY Lock from Setup a menuSetup the KEY Lock Select Setup B Menu Serial Control LAN Setting OSD Select OSD from Setup B menuSetup the function Setup the turn off time Select Rotation from OSD menu Setup the RotationSelect OSD H Positiion Select OSD V Positiion Select Transparency from OSD menu Setup the Info DisplaySetup the Transparency Select Info Display from OSD menu Setup the OFF Timer OFF TimerSetup B Reset Select OFF Timer from Setup B menu Select Option menu Factory ResetSelect Factory Reset from Setup B menu Sub-menus can be configured Change Security Password Input Resolution Group ID Tiling Menu Lock Select IR Control from Option menu Setup the Tiling Select the IR ContolIR Control Tiling Power on Input Detect Power on Delay No image at upper and lower part of the screen Before calling for serviceApplicable signals Tick sound from the main body EN61000-3-2 SpecificationRegulatory Information EN61000-4-8 Magnetic Field Immunity EN61000-4-11 Memo Dimension