Inserting the batteries | PLUS Vision U2-1130/U2-1110 specification

For video equipment connection

Audio video cable	S-video cable
(1 m/3.3 ft.) [1]	(1 m/3.3 ft.) [1]

Lens cap (attached to the lens of the unit) [1]

About the lens cap

The lens cap is fixed on the bottom of the unit as shown in the illustration below.

Carrying case [1]

How to use the carrying case

Packing the unit

Packing the accesories

P r e p a r i n g t h e

r e m o t e c o n t r o l

Inserting the batteries

1 Press firmly and slide the battery cover off.

2 Insert the two supplied batteries (size AA/R6). Ensure that the polarities (+ and –) of the batteries are aligned correctly.

3 Slide the cover back until it snaps into place.

Notes

•If the remote control gets wet, wipe it dry immediately.

•Avoid excessive heat and humidity.

•If you will not be using the remote control for a long time, remove the batteries.

•Do not mix new and old or different types of batteries.

•There are operations that can only be carried out by remote control. Handle the remote control carefully.

Remote control effective range

The remote sensors are located on the front and back of the unit.

The controllable range is 50 degrees horizontally and 30 degrees vertically relative to a line that is at a right angle to the remote sensor. And the distance between the point of the remote control and remote sensor must be shorter than four meters (13 feet).

MOUSE

RGB IN

PC AUDIO	S-VIDEO

VIDEO	AUDIO
	L/MONO	R

	USER’S MANUAL	Quick Start Guide [1]
	(this manual) [1]	Quick Start Guide [1]
	(this manual) [1]

30˚ 50˚

50˚

30˚

E – 5

Image 7

PLUS Vision U2-1130/U2-1110 user manual E p a r i n g t h e M o t e c o n t r o l, Inserting the batteries

Contents

U2-1130/U2-1110 Plus Corporation U2-1130/U2-1110 English Power Supply PrecautionsImportant Safeguards Installation B l e o f c o n t e n t s Serial mouse cable Mouse adapter For IBM PS/2 Power cable mains lead 1.8 m/5.9 ftA t u r e s E c k i n g t h e P p l i e d a c c e s s o r i e s E p a r i n g t h e M o t e c o n t r o l Remote control effective rangeInserting the batteries Menu button RGB in connectorR t s a n d c o n t r o l s Top, front and side panel view Built-in Security Slot Lamp cover securing screw Rear adjusterRear and side panel view Bottom Freeze button Mute button Click button 14 Screen InstallationPositioning the unit Projecting distance and image size Using the ceiling mounting fixtures Installation c o n t i n u e d N n e c t i o n s Units terminal panel Connector Before connectingN n e c t i n g a P C o r M a c i n t o s h 3 4 5 Modifying the DIP switch setting for Macintosh How to connect to the IBM PS/2 or Macintosh computer How does the remote control operate the computer?Connecting the computer to the Mouse connector of the unit How to connect to the IBM PC/AT computer View from the top Adjust the position and height of the unitI n g t h e u n i t Before starting Then adjust the focus with the focus ring Adjust the image size with the zoom ringI n g t h e u n i t c o n t i n u e d Amber After using the unit Windows Windows 98/WindowsMacintosh Freezing a moving picture Adjusting the volume of the units speakerUsing the laser pointer Turning off the image and muting the sound temporarily Press Magnify Enlarging the picturePress Pointer Press Magnify + Pointer N u s t r u c t u r e When the input source is Video or S-VIDEO Operating using the unit L e c t i n g t h e c o l o r s y s t e m R r e c t i n g t h e Y s t o n i n g e f f e c tL e c t i n g a m e n u l a n g u a g e L e c t i n g a O j e c t i o n t y p e L e c t i n g t h e b a c k g r o u n d L e c t i n g t h e p o i n t e r t y p eJ u s t i n g t h e v o l u m e Timing Chart Adjusting the clock phase Setting the input source to RGBSetting Auto Mode to OFF for manual ad- justment Adjusting the clock frequency L e c t i n g t h e p i c t u r e t y p e J u s t i n g t h e C t u r e e l e m e n t s T i v a t i n g t h e o n s c r e e n f u n c t i o n T i v a t i n g t h e p o w e r s a v i n g f u n c t i o nI c k s t a r t i n g t h e u n i t E c k i n g h o u r s o f l a m p u s a g e Resetting the lamp usage hours to zeroS e t t i n g t o t h e f a c t o r y s e t t i n g s Common Problems & Solutions Troubleshooting Status Light Messages Status indicator P l a c i n g t h e l a m p c a r t r i d g e Lamp cartridge replacement procedureStep Optical Specification s PC 15-Pin mini D-Sub Sub Pin Assignments U2-1130 DimensionsU2-1110 Plus Corporation