R

EDGE 60 Pellet Fireplace

F. Recommended Sequence of Installation

G. Items to Verify During Test Burn

NOTICE:

•Read and understand Sections 6 through 10 for detailed information before installing the fi replace.

•Follow all clearances as specifi ed.

•The choice of fi nishing material and decorative front must be determined before installation can begin as it will determine the placement of the fi replace.

•Outside air is required on all installations and the Outside Air Kit must be ordered separately.

•Check for leaks in the exhaust venting system. Do you see any smoke?

Remember on a fi rst burn odors and vapors are released due to the curing of the high tem- perature paint. The focus is on the venting system.

•Check overall operation, are there any error codes on the Wall Control?

•Confi rm that outside air is hooked up and properly sealed. Is there cold air infi ltration?

 

Recommended Sequence

 

 

1.

Identify the exhaust vent and outside air locations

 

and install necessary venting components including

 

wall thimble, fi re stop or roof fl ashing for a verti-

 

cal termination. NOTE: Outside Air Kit must be

 

ordered separately.

 

 

2.

Complete the framing.

 

 

3.

Install the electrical junction box near the electrical

 

opening on the left side of the appliance. Maximum

 

distance of 9 inches (229mm) from appliance.

 

 

4.

Identify the location of the wall control and run the

 

wire (25 ft [7.62 meters] in length) to the left side of

 

the appliance.

 

 

5.

Prepare the fi replace for the exhaust vent adapter.

 

Install adapter, seal with high temp silicone and

 

screws and install all cover plates.

 

 

6.

Preset the nailing fl anges depending on the thick-

 

ness of your fi nishing material.

 

 

7.

Ensure that fi replace is level before securing in

 

place. If not level the decorative front will not swing

 

out properly.

 

 

8.

IT IS CRUCIAL FIREPLACE IS ROBUSTLY

 

SECURED. Slide the fi replace into place and

 

secure to the fl oor with the securing brackets and to

 

the wall. See page 33 for detailed instructions.

 

 

9.

Attach the exhaust and outside air venting to the

 

appliance.

 

 

10.

Hook up power and the wall control.

 

 

11.

Slide the fi replace out on the rail system to validate

 

that it is secure and there is no defl ection in the

 

outer can.

 

 

12.

Slide the fi replace back into the outer can. Re-attach

 

the bolts and brackets. Double check they are cor-

 

rectly positioned to ensure the exhaust gaskets are

 

properly sealed to prevent combustion leakage.

 

 

13.

A burn test must be performed before fi nishing

 

material is installed. (See Item “G”).

 

 

14.

Install the fi nishing material.

 

 

15.

Install the decorative front.

 

 

WARNING

Crush Hazard!

To avoid tipping over, this appliance must be securely fastened to the fl oor.

•The fi replace must be secured in place as outlined in Section 6 and 7.

•When servicing the fi replace, the fi replace slides foward on the rail system.

•Tipping can occur if fi replace is not properly secured to the fl oor.

December 6, 2011

7051-158B

Page 25

Page 24 Page 26
Page 25
Image 25
Quadra-Fire 7051-158B owner manual Crush Hazard, Recommended Sequence, Material is installed. See Item G
Page 24 Page 26

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.
Top Page Image Contents