R

EDGE 60 Pellet Fireplace

C. Convection Blower Replacement

D. Baffl e Removal & Replacement

1.Follow the proper shut down procedures as outlined on page 14, Section 3.A.

2.Remove the 2 bolts from the bottom left and right side of the fi replace and slide the fi replace out.

3.Locate the convection blower on the bottom left rear of the fi replace. Reach behind the blower and release the latch by pushing the top of the latch towards the blower. Figure 50.1.

4.Rock the top of the blower slightly and lift up and out. The blower will pass around the control board and out the side of the fi replace.

5.Disconnect the wire harness from the bottom of the blower by depressing the tabs on the sides of the con- nector and then pulling to remove.

6.Re-connect wire harness to the new replacement blower. Install the blower by placing the bottom fl ange into the opening fi rst then rotate blower up into posi- tion.

7.When the blower is properly positioned the latch will engage the notch to hold the blower in place. Figure 50.2.

8.Slide appliance back in position and re-install bolts.

RELEASE THE LATCH

Figure 50.1

Figure 50.2

WARNING! Risk of Injury! Cast iron is a very heavy material. The baffl e is made of cast iron and therefore is heavy and awkward at times to maneuver. Clear and prepare your work area before you begin.

1.Follow the proper shut down procedures as outlined on page 14, Section 3.A.

2.Open front and open fi rebox door.

3.The baffl e is located at the top inside of fi rebox.

4.To remove the baffl e:

a.Place a fl at head screwdriver into the slot of the latches located in the upper corners. Figure 50.3.

b.Push down and the bottom of the latch will fall forward off of the post.

c.Lift the baffl e up and then out toward you.

5.To replace the baffl e:

a.Place the 2 locating ears behind the bottom edge.

b.Tilt the baffl e up and into place.

The baffl e must be centered in the fi rebox before latching it in place.

c.If it is not centered the latch is trapped between the baffl e and side of the fi rebox instead of latch- ing properly.

d.The bottom of the latches will fi t over the posts.

e.Push the top of the latch forward to lock latch into place.

Baffle

Latches

Locating ears - 1 on

Insert flat head screw driver into “V”

each side. Fit behind

bottom edge.

section and push down and the bottom

 

of the latch will fall forward off of post

 

Figure 50.3

December 6, 2011

7051-158B

Page 51

Page 50 Page 52
Page 51
Image 51
Quadra-Fire 7051-158B owner manual Convection Blower Replacement Baffl e Removal & Replacement
Page 50 Page 52

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.
Top Page Image Contents