Vertical Installation

EDGE 60 Pellet Fireplace

E. Thermostat Wall Control Installation	F. Installing Flue Collar, Vertical or Horizontal

NOTICE: The thermostat wall control should be mounted on an inside wall and not in direct line with the appliance convection air.

NOTICE: If the thermostat wall control is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired temperature in your home.

Consideration should be given to the mounting material when installing the wall control.

If mounting the wall control to a sheet rock surface you should use the provided anchors for mounting.

If mounting the wall control to a wood surface or an electri- cal outlet box then the fasteners provided will sufﬁ ce and the anchors need not be used.

1.Remove the front cover of the wall control by prying the cover off with a small screwdriver or your ﬁ ngernail. Place the front side to the packaging to protect it from damage while installing the sub base.

2.Route the wires into the wall control leaving only the amount necessary to make the connection to the terminal block in the upper left hand corner remaining. The wires are routed to the terminal block according to the letters printed in the thermostat sub base.

Red at the top

Green in the middle

White at the bottom

3.Push as much extra wire as possible back into the wall and seal the hole in the wall with putty or insulation.

4.When re-installing the cover make sure that the wire routing does not interfere with any of the components. Make adjustments as needed and snap cover back into place making sure that all locking tabs snap into place.

The ﬁ replace ships from the factory without the ﬂ ue collar and gasket attached. They are located in the component pack inside the ﬁ rebox. Follow the steps below for a vertical or horizontal installation.

1.Remove the ﬂ ue collar and gasket from the component pack. Push out the 6 slugs in the gasket.

2.Remove both the top and rear cover plates. Save screws and plates for later re-attachment.

3.Place the orange ﬂ ue gasket over the locating pins on the exhaust ﬂ ue transition on the back of the ﬁ replace. Figure 35.2.

4.Insert the ﬂ ue pipe through the top cover plate.

5.Before inserting the ﬂ ue collar into the pipe, liberally silicone the end of the ﬂ ue collar with Hi-Temp silicone about 1-1/2 inches (38mm) wide. Figure 36.1 on page 36.

NOTE: You will need to install one section of 3 inch (76mm) diameter vent pipe to clear the outer can cover plate before installing a 3 to 4 inch (76-102mm) pellet pipe adapter for the balance of the venting.

6.Lay the ﬁ rst section of pipe on its side for screw attach- ment. The 2 screws need to be directly above the locat- ing pins, 180 degrees apart. Figure 36.2 on page 36.

7.Drill holes through the pipe walls directly into the ﬂ ue collar. Attach screws through pipe into ﬂ ue collar.

8.Carefully feed the ﬂ ue collar and pipe through the outer can top ﬂ ue opening and guide the ﬂ ue collar base plate over the 2 locating pins. Secure with 4 screws provided in component pack.

9.Re-attach the top cover plate to the top of the ﬁ replace and the rear cover to the back of the outer can. Figure 36.4 on page 36.

Top

Red Wire

Green Wire

White Wire

Bottom

Figure 35.1- Back Side of Wall Control with Cover Off

4 screws in outer corner holes

Locating Pins

Figure 35.2- Install Orange Flue Gasket

Page 36

7051-158B

December 6, 2011

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.

Quadra-Fire 7051-158B owner manual Vertical Installation, Back Side of Wall Control with Cover Off

Models: 7051-158B