Regency F39-LPG Dura-Flue Horizontal Installations, Diagram, Hint Apply silicone to female end

INSTALLATION

945B	45O Elbow-Black
945G	45O Elbow-Swivel Galv.
945BG	45O Elbow-Swivel-Black
990	90O Elbow Galv.
990B	90O Elbow-Black
990G	90O Elbow-Swivel Galv.
990BG	90O Elbow-Swivel-Black
991	High Wind Term. Cap (Vertical)
980	Vertical Term. Cap
982	Snorkel-14" Rise Term.Cap
981	Snorkel-36" Rise Term.Cap

940Wall Thimble-Support/Box

941Cathedral/Ceiling-Support/Box

3951 Brass Trim-Wall Thimble/ Ceiling Support

963 Firestop Spacer

943Flashing 0/12-6/12

943S Flashing 7/12-12/12

953	Storm Collar
950	Vinyl Siding Standoff
988	Wall Strap
942	Wall Thimble

Parts not supplied by Dura-Flue 946-506/P Flue Guard (Optional)

DURA-FLUE

HORIZONTAL

INSTALLATIONS

1)Set the unit in its desired location. Check to determine if wall studs or roof rafters are in the way when the fl uing system is attached. If this is the case, you may want to adjust the location of the unit.

2)Room Sealed pipe and fi ttings are designed with special twist-lock connections to con- nect the fl uing system to the appliance fl ue outlet. A twist-lock appliance adaptor is installed on the unit at the factory.Assemble the desired combination of

pipe and elbows to the ap- pliance adaptor with

pipe seams oriented towards the wall or ceiling, as much out of

view as possible. The

final positioning of the pipe and 90o elbow as- sembly is determined by the mounting

orientationofthe adaptor on the stove and twist- lockedforasolid connection.

Note:

a)Twist-lockprocedure:Fourindentations, located on the female ends of pipes and fi ttings, are designed to slide straight onto the male ends of adjacent pipes and fi ttings, by orienting the four pipe indentations so they match and slide in to the four entry slots on the male ends

(diagram 1). Push the pipe sections completely together, then twist-lock one section clockwise approximately one-quarter turn, until the two sections are fully locked. The female locking lugs will not be visible from the outside on the Black Pipe or fi ttings. They may be located by examining the inside of the female ends.Apply sealant "Mill-Pac" to innerpipeandhightempsiliconesealant to outer pipe on every twist-lock joint.

Hint: Apply silicone to female end.

b)Horizontalrunsoffluemustbesupported everythreefeet.Wallstrapsareavailable for this purpose.

3)With the pipe attached to the stove, slide the stove into its correct location, and mark the wall for a 10" x 10" (inside dimensions) square hole. The center of the square hole should line up with the centerline of the

Diagram 1

horizontal pipe, as shown in diagram 2. Cut and frame the 10 inch square hole in the exterior wall where the fl ue will be terminated. If the wall being penetrated is constructed of non-combustible material, i.e.masonryblockorconcrete,a7"diameter hole is acceptable.

Note:

a)The horizontal run of fl ue should have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the fl ue to run downward. This could cause high temperatures and may present the possibility of a fi re.

F39: 59-3/4" (1518mm)

Diagram 2

b)The location of the horizontal fl ue termi- nation on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. For External Flue Terminal Locations dia- gram, refer to "Exterior FlueTermination Location" section.

4)If installing the fl ue termination to a wall with vinyl siding, the Vinyl Siding Standoff must be used. Attach the Vinyl Siding Standoff to the Horizontal FlueTermination, but first run a bead of non-hardening mastic around its outsideedges,soastomakeasealbetween fl ue cap and the standoff. Install the Vinyl Siding Standoff (Part # 950) between the fl ue cap and the exterior wall and attach with the four wood screws provided. Seal around the Vinyl Siding Standoff on all four sides. Diagram 5. The arrow on the flue cap should be pointing up. Insure that the 1-1/4" clearances to combustible materials are maintained. See diagram 5.

	Diagram 5
Note:	If installing termination on a siding

covered wall, a vinyl siding standoff or fur- ring strips must be used to ensure that the termination is not recessed into the siding. The four wood screws provided should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

5)Before connecting the horizontal run of fl ue pipe to the fl ue termination, slide the black decorative wall thimble cover over the fl ue pipe, then slide the Wall Thimble (Part # 942) over the fl ue pipe.

6)Slide the appliance and fl ue assembly towards the wall carefully inserting the fl ue pipe into the fl ue cap assembly. It is impor- tant that the fl ue pipe extends into the fl ue cap a suffi cient distance so as to result in a minimum pipe overlap of 1-1/4 inches. Secure the connection between the fl ue pipe and the fl ue cap using sheet metal screws provided. See diagram 6.

7)Install the Wall Thimble in the center of the 10" square and attach with wood screws.

Regency® F39 Room Sealed Freestanding Gas Stove 13