Regency L900-LP, L900-NG Installation, L676 & L900 Direct Vent Fireplace, Offset Pipe Selection

INSTALLATION

INSTALLATION

Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.

Description		Simpson		Simpson		Selkirk	Metal-Fab®
			®	Direct Vent GS®
		Direct Vent Pro		Discontinued		Direct-Temp™	Sure Seal
Round Support / Radiation Sheild		N/A		N/A		N/A	N/A
Flat Flashing		N/A		N/A		N/A	N/A
Attic Insulation Shield 12”		58DVA-IS - N/A from FPI		58DVA-IS - N/A from FPI		N/A	N/A
Basic Horizontal Termination Kit (A)		N/A		N/A		5DT-HKA	N/A
Horizontal Termination Kit (B)		58DVA-KHA		N/A		5DT-HKB	N/A
Vertical Termination Kit		58DVA-VCH		1291		5DT-VKC	N/A
High Wind Vertical Cap		N/A		N/A		N/A	N/A
High Wind Horizontal Cap		DISC.		1285		N/A	N/A
Horizontal Square Termination Cap		N/A		1284		5DT-HHC	5DHT
Vertical Termination Cap		N/A		N/A		5DT-HVC	5DVT
Storm Collar		58DVA-SC		1253		5DT-SC	5DSC
Adjustable Flashing, 0/12-6/12		58DVA-F6		1243		5DT-AF6	5DF
Adjustable Flashing, 6/12-12/12		58DVA-F12		1243S		5DT-AF12	5DF-12
Vinyl Siding Standoff		58DVA-VSS		1250		5DT-VS	5DVS
Vinyl Siding Shield Plate		N/A		N/A		5DT-VSP	N/A
Snorkel Termination 14”		58DVA-SNK14		1282		5DT-ST14	5DST14
Snorkel Termination 36”		N/A		1281		5DT-ST36	5DST36
Restrictor Disk		58DVA-RD		N/A		N/A	N/A
Colinear Flex Liner Adapter (3” Ø)		N/A		N/A		N/A	N/A
FPI
946-604/P	Simpson Direct Vent Vent Guard (Optional)			946-623/P	AstroCap XL Horizontal Cap
770-994	Rigid Pipe Adapter (Must use with all Rigid Piping)			946-506/P	Vent Guard (Optional)
				946-625	Vinyl Siding Standoff - AstroCap XL

*NOTE: When using Metal-Fab Sure Seal Rigid Piping please note that either the Adaptor (5DDA) or 90º Starter Elbow (5D90A) must be used in conjunction with FPI Rigid Pipe Adaptor (770-994).

L676 & L900 Direct Vent Fireplace

IMPORTANT NOTE

•A Vent Guard is required when the AstroCap is installed above grade at 7 feet or lower.

•The Simpson Dura-Vent and Selkirk Direct Temp horizontal termination caps cannot be used in any applications.

•Only the AstroCap XL and Snorkels are certified for horizontal terminations.

Offset Pipe Selection:

Use this table to determine offset pipe lengths.

Pipe Length	5” x 8” Venting
	Run (X)	Rise (Y)
0”(0mm)	5-11/16”(144mm)	15-5/16”(389mm)
6”(152mm)	8-13/16”(224mm)	18-7/16”(468mm)
9”(229mm)	10-15/16”(278mm)	20-9/16”(522mm)
12”(305mm)	13”(330mm)	22-11/16”(576mm)
24”(610mm)	21-7/16”(697mm)	31-1/16”(789mm)
36”(914mm)	29-13/16”(757mm)	39-7/16”(1002mm)
48”(1219mm)	38-1/4”(972mm)	47-7/8”(1216mm)

L

Y

X

For specific instructions or details on particular venting components please visit the following websites:

Simpson Direct Vent Pro: www.duravent.com

Selkirk Direct-Temp: www.selkirkcorp.com

Metal-Fab Sure Seal: www.mtlfab.com

NOTE: Horizontal runs of vent must be level, or have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present a possible fire hazard.

18 Regency® L900 Direct Vent Gas Fireplace