Features, Product Specifications, RIP Fence | RIDGID TS3660 specification

FEATURES

PRODUCT SPECIFICATIONS

Blade Diameter	10 in.
Blade Arbor	5/8 in.
Cutting Depth at 0°	3-3/8 in.
Cutting Depth at 45°	2-1/4 in.

Rating	120 V, AC Only, 60 Hz, 13	Amps
	240 V, AC Only, 60 Hz, 6.5	Amps
No Load Speed	3,450 r/min. (RPM)

		BEVEL
		LOCK
		LEVER
ANTI-KICKBACK			BEVEL
PAWLS			BEVEL
PAWLS			ADJUSTING
SEPARATOR	BLADE GUARD	SAW	HANDWHEEL
SEPARATOR	BLADE GUARD
(SPLITTER)	ASSEMBLY
(SPLITTER)	ASSEMBLY	BLADE
		BLADE
		RIP FENCE
			FRONT
MITER			RAIL
MITER
GAUGE		SWITCH
		SWITCH	LOCKING
		ASSEMBLY	LEVER
RIP FENCE		BEVEL SCALE
STORAGE		MITER GAUGE
HOOKS		MITER GAUGE
		STORAGE HOOK

LEG
STAND	HEIGHT
	ADJUSTING
	HANDWHEEL

BLADE HEIGHT

LOCK KNOB

HERC-U-LIFT™

LEVELING

FOOT

MOBILE BASE

Fig. 6

Page 12

Image 12

RIDGID TS3660 manual Features, Product Specifications, RIP Fence, Bevel Scale

Contents

OPERATOR’S Manual Table of Contents Introduction General Safety Rules Read ALL Instructions Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Blade Coasts After Being Turned OFF  Never Operate the SAW on the Floor Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATION Service Authorized Service Center for repair. When servic Speed and Wiring ElectricalExtension Cords Electrical Connection Changing Motor Voltage See Figures 2 Junction BOX Manual Reset Button Motor Thermal Overload ProtectorSee Figure Glossary of Terms Features Product SpecificationsRIP Fence Bevel Scale Know Your Table SAW Overview Tools Needed HEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16Square Framing Square Loose Parts Key Description Qty Loose Parts List Assembly UnpackingMounting Holes To Assemble LEG Stand and Storage Brackets To Install Extension Tables To Mount the Table SAW to the LEG StandScrew With Washer To Install the HERC-U-LIFT Mobile Base to the LEG Stand To Install Bevel Adjusting HAND- Wheel To Install Height Adjusting HAND- WheelLock Blade Tube Height Lock Knob Adjusting Handwheel To assemble the Herc-U-Lift to the leg stand To Store Accessories To Install Front and Back RailsTool Storage Square Head Bolt Square Head Bolt To Adjust Front and Back Rails See Figures 23Front Rail Rear Shims To Install RIP Fence To Check the Throat PlateSET Screws RIP Fence in Locked Position Unlocked Position See Figures 27 To Install Spacer BAR To Install Blade Guard AssemblyTo Align Blade Guard Assembly to the Blade To Mount Motor Assembly To Install the Belt GuardTo Install Belt Motor Assembly To Install Switch Assembly To Install END CapsTo Secure the Electrical Cords To Adjust Blade Depth To Adjust Blade Angle Operation HOW to Make a Featherboard FeatherboardPush Sticks Push Blocks See Figures 41 Types of Cuts Cutting TipsCross CUT To USE the IND-I-CUT Feature To USE the HERC-U-LIFT Mobile Base to Move the Table SAWUnlock Pedal Metal Platform To USE the MICRO-ADJUST Feature on the RIP Fence MICRO-ADJUST Wheel Dust ChuteTo USE the SAW Dust Chute See Figures 46 Switch KEY Removed Switch on To Make a Cross CUTSee Figures 49 To Make a RIP CUT To Make a Miter CUT To Make a Bevel Cross CUT To Make a Bevel RIP CUTViewed from the FRONT, below the Table SAW To Tighten To Make a Compound Bevel Miter CUT Bevel RIP CUT Blade AngledScale RIP Fence To Make a Large Panel CUT To Make a NON-THROUGH CUT NON-THROUGH CUT To Make a Dado CUT Dado CUT Adjustments To Install Zero Clearance Throat PlateTo REMOVE/REPLACE the Throat Plate Removing Throat Plate Zero Clearance To Replace the SAW Blade See Figures 62Blade Wrench Washer NUT Framing Square Heeling Paralleling the Blade to the Miter Gauge Groove See Figures 64Trunnion Bolt Trunnion Bolt Lever To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚ See Figures 67Screws Bevel Lock Lever Blade AT 90˚ Position To Adjust the Bevel Adjusting HAND- Wheel To Adjust the Miter Gauge To Align and Adjust the RIP Fence Locking Lever HEX Head Screws Adjusting NUT Back RailSee Figures 74 To Adjust the RIP Fence Indicator PAN Head Screw Maintenance AccessoriesGeneral Maintenance Lubrication Troubleshooting Problem Cause Solution Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not Covered Customer Service Information Model No TS3660 Serial No

FEATURES

PRODUCT SPECIFICATIONS

3,450 r/min. (RPM)

RIP FENCE

BEVEL SCALE