Turning on the Power, Connecting to AC Power | Runco V-63HD, V-50HD

Installation

Connecting to AC Power ➤

3.5

Turning on the Power

The V-50HD/V-63HD ships with two (2), AC power cords: one for the DHD Controller and one for the display.

1.Plug the female end of one of the power cords into the AC receptacle on the rear of the V-50HD/V-63HD (AC 100V ~ 240V); see Figure 2-3.

2.Connect the other end to your AC power source.

3.Re-attach the AC input cover plate, routing the power cord through the slot on the plate.

4.Connect the DHD Controller to a nearby AC outlet using the other AC power cord.

1.Power up your source components.

2.Press the ON button on the remote control to turn on the system. The front-panel status indicator on the DHD Controller flashes blue to indicate that it is powering up.

3.When the display is ready for use, the front-panel status indicator on the DHD Controller lights solid blue.

24	Vistage™ Series Flat-Panel Display Installation/Operation Manual

Image 36

Runco V-63HD, V-50HD operation manual Turning on the Power, Connecting to AC Power

Contents

Vistage Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Maintenance and Troubleshooting SpecificationsOperation External Control List of Figures List of Figures Introduction About This Manual Using This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunction Description, Features and Benefits Optional Accessories Indicators Controls and FunctionsVistage Series at a Glance Front-Panel Controls Remote Control Sensor DHD Controller Front Panel Primary Input Messages from the Hdmi Audio Out connector DHD Controller Rear Panel V-50HD/V-63HD Remote Control Unit DHD Controller/V-50HD/V-63HD Remote Control Light For more information about aspect ratios, refer to Table Cinema Controls and Functions Installation Remote ControlInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer Operation Installation Considerations Synchronization IssuesPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table Stand Ambient Light Other ConsiderationsRack-Mounting the DHD Controller Connecting the DHD Controller to the V-50HD/V-63HD Connections to the V-50HD/V-63HD and DHD ControllerUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not work Connecting Source Components to the DHD Component Video Source Connections Rgbhv Source Connections Composite Video Source Connections Connecting an Audio Processor or SecondaryDisplay Device to the DHD Controller Optional RS-232 Controller ConnectionEthernet Network Turning on the Power Connecting to AC Power Setting the Computer Display Properties Operation Operation Using the On-Screen Menus Input Position Service Main Menu Input SourceAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in their Remote Aspect Ratio Control Description Key Native Screen PictureScreen Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Sleep Timer Sleep Timer Signal InformationInformation System You must enter a passcode to access the Calibration menu Calibration ISF SettingsCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copied settings are not retained after a power cycle Memory PresetCopy/Paste Keystone and Pincushion Distortion Left Middle y setting also controls the Right Middle Image Alignment Controls You must enter a passcode to access the Service menu ServiceTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Logo LED setting Regardless of the Standby LED setting38 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes Solution Troubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial Communications Serial Commands Input Selection Commands Picture Adjust Commands Input Position Commands Output Shift Commands Screen Commands Miscellaneous Commands Using Discrete IR Codes Command Parameter min/max Value Stored? DescriptionEnter key Exit key Command Bits With Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerRC5 Data ST60MIN Using Hdmi CEC Messages CEC Commands Supported by the DHD ControllerOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control Specifications V-50HD/V-63HD SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications 50HD Dimensions 1shows the V-50HD dimensions 63HD Dimensions 2shows the V-63HD dimensions Supported Signal Timings by Input Supported TimingsComponent Composite 1 Composite 2 Composite Format Resolution Frequency Rate Hz MHz KHz Rgbs PAL-M Specifications Page 020-1114-00 Rev. a April