Information, Signal, System, Network | Runco V-63HD, V-50HD specification

Operation

Information ➤

Information

Signal

System

Network

Field Service

Signal / System: Select Information from the Main Menu, then choose either Signal or System to display information about the current input signal (resolution, frequency, type et cetera) and installed firmware versions, as well as other information that uniquely identifies your DHD Controller and display device.

Should you ever need to contact Runco Technical Support, this information will help them answer your questions or resolve product performance issues.

Manufacturing

	Signal
Input Source	HDMI 1
Signal Format	1080p/60
Input Resolution	1920x1080
Vertical Freq	59.94 Hz
Horizontal Freq	67.500 kHz
Pixel Clock	148.500 MHz
Color Space	REC709
Sync Type	Separate
Memory Preset	ISF Night

System

Model	DHD-LS
Display Name	V-50HD/V-63HD
Output Resolution	1920x1080
Serial Number	00000000
Boot Version	4.0
Firmware Version	4.0
Micro Version	4.0

Network

MAC Address	1A:2B:3C:4D:5E:6F
IP Address	192.168.0.150
Subnet Mask	255.255.0.0
Default Gateway	192.168.1.1
DHCP	Enabled
Network Status	Connected

Network: Select Information from the Main Menu, then choose Network to display information about the Ethernet network connection.

To enable network communication via Ethernet, refer to IP Configuration on page 48.

Field Service / Manufacturing: The Field Service and Manufacturing menus are password-protected and intended for use only by Runco service personnel and factory technicians.

40	Vistage™ Series Flat-Panel Display Installation/Operation Manual

Image 52

Runco V-63HD, V-50HD operation manual Information, Signal, System, Network

Contents

Vistage Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Maintenance and Troubleshooting SpecificationsOperation External Control List of Figures List of Figures Introduction About This Manual Using This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunction Description, Features and Benefits Optional Accessories Indicators Controls and FunctionsVistage Series at a Glance Front-Panel Controls Remote Control Sensor DHD Controller Front Panel Primary Input Messages from the Hdmi Audio Out connector DHD Controller Rear Panel V-50HD/V-63HD Remote Control Unit DHD Controller/V-50HD/V-63HD Remote Control Light For more information about aspect ratios, refer to Table Cinema Controls and Functions Remote Control InstallationInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer Operation Installation Considerations Synchronization IssuesPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table Stand Ambient Light Other ConsiderationsRack-Mounting the DHD Controller Connecting the DHD Controller to the V-50HD/V-63HD Connections to the V-50HD/V-63HD and DHD ControllerUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not work Connecting Source Components to the DHD Component Video Source Connections Rgbhv Source Connections Composite Video Source Connections Connecting an Audio Processor or SecondaryDisplay Device to the DHD Controller Optional Connection RS-232 ControllerEthernet Network Turning on the Power Connecting to AC Power Setting the Computer Display Properties Operation Operation Using the On-Screen Menus Input Position Service Input Source Main MenuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in their Remote Aspect Ratio Control Description Key Native Screen PictureScreen Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep Timer Signal InformationInformation System Calibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Left Middle y setting also controls the Right Middle Image Alignment Controls Service You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes Solution Troubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial Communications Serial Commands Input Selection Commands Picture Adjust Commands Input Position Commands Output Shift Commands Screen Commands Miscellaneous Commands Using Discrete IR Codes Command Parameter min/max Value Stored? DescriptionEnter key Exit key Command Bits With Toggle Bit = Hex Binary Function Start RC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications 50HD Dimensions 1shows the V-50HD dimensions 63HD Dimensions 2shows the V-63HD dimensions Supported Signal Timings by Input Supported TimingsComponent Composite 1 Composite 2 Composite Format Resolution Frequency Rate Hz MHz KHz Rgbs PAL-M Specifications Page 020-1114-00 Rev. a April