Sleep Timer | Runco V-50HD, V-63HD instruction

Operation

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

•Brightness

•Contrast

•Color saturation

•Tint

•Sharpness

•Gamma

•Color temperature and white balance

To select a memory preset, press or to highlight it and press ENTER.

To save the settings for the current input and display mode to the Custom 1 or Custom 2 memory preset, select it, press or to highlight Save and press ENTER.

To save the settings for the current input and display mode to the

Note ISF Night or ISF Day memory preset, select Save ISF Night or Save ISF Day from the Calibration menu (refer to Save ISF Night/Save ISF Day on page 44).

To reset the Custom 1 or Custom 2 memory preset to its factory-default state, select it, press or to highlight Reset and press ENTER.

Select Sleep Timer from the Main Menu to turn off the V-50HD/V-63HD after a specified interval. Press or to select Off, 30 Minutes, 60 Minutes, 90 Minutes, 2 Hours or

4 Hours. Then, press ENTER.

Sleep Timer

Sleep Timer

ÎOff

30 Minutes

60 Minutes

90 Minutes

2 Hours

4 Hours

Vistage™ Series Flat-Panel Display Installation/Operation Manual

39

Image 51

Runco V-50HD, V-63HD operation manual Sleep Timer

Contents

Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents External Control Maintenance and TroubleshootingSpecifications Operation List of Figures List of Figures About This Manual Introduction Degrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental information Description, Features and Benefits Optional Accessories Front-Panel Controls IndicatorsControls and Functions Vistage Series at a Glance Remote Control Sensor Primary Input DHD Controller Front Panel DHD Controller Rear Panel Messages from the Hdmi Audio Out connector DHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control Unit For more information about aspect ratios, refer to Table Light Cinema Controls and Functions Installation Remote ControlInstallation specialist Operation Quick SetupInstallation Overview Step Procedure For Details, Refer Mounting the V-50HD/V-63HD on a Wall or Table Stand Installation ConsiderationsSynchronization Issues Possible Audio Latency for Various Input Timings Controller Ambient LightOther Considerations Rack-Mounting the DHD DVI-to-HDMI adapters will not work Connecting the DHD Controller to the V-50HD/V-63HDConnections to the V-50HD/V-63HD and DHD Controller Use an Hdmi cable for this connection. a DVI cable with Components to the DHD Connecting Source Component Video Source Connections Rgbhv Source Connections Composite Video Source Connections Controller Optional Connecting an AudioProcessor or Secondary Display Device to the DHD RS-232 Controller ConnectionEthernet Network Connecting to AC Power Turning on the Power Operation Setting the Computer Display Properties Operation Input Position Using the On-Screen Menus Service Main Menu Input SourceAspect Ratio Hdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDs Native Remote Aspect Ratio Control Description Key Picture ScreenPicture Screen Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Sleep Timer Sleep Timer System SignalInformation Information You must enter a passcode to access the Calibration menu Calibration ISF SettingsCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copied settings are not retained after a power cycle Memory PresetCopy/Paste Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right Middle You must enter a passcode to access the Service menu ServiceTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Logo LED setting Regardless of the Standby LED setting38 and ISF Day/Night Memory Presets Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting Chart Troubleshooting Chart Serial Communications Port ConfigurationSerial Command Syntax External Control Input Selection Commands Serial Commands Picture Adjust Commands Output Shift Commands Input Position Commands Miscellaneous Commands Screen Commands Exit key Using Discrete IR CodesCommand Parameter min/max Value Stored? Description Enter key With Toggle Bit = Hex Binary Function Start Command Bits Remote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerRC5 Data ST60MIN Using Hdmi CEC Messages CEC Commands Supported by the DHD ControllerOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control Specifications V-50HD/V-63HD SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications 1shows the V-50HD dimensions 50HD Dimensions 2shows the V-63HD dimensions 63HD Dimensions Composite 1 Composite 2 Composite Supported Signal Timings by InputSupported Timings Component Rgbs Format Resolution Frequency Rate Hz MHz KHz PAL-M Specifications Page 020-1114-00 Rev. a April