Cinema | Runco V-50HD, V-63HD specs

Controls and Functions

10.HD 1 (4) / HD 2 (5)

Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric character “4” or “5.”

11.COMP (Component) (6)

Press to select the Component video input as the source or to enter the numeric character “6.”

12.HDMI 1 (7) / HDMI 2 (8) / HDMI 3 / HDMI 4 (0)

Press to select an HDMI input as the source or to enter the numeric character “7,” “8” or “0.”

13.SCART (9)

Press to select the SCART video input as the source or to enter the numeric character “9.”

14.Aspect Ratio Selection Buttons

Use these buttons to select an aspect ratio directly, as follows:

NATIVE

Displays the source signal in its native resolution, centered in the display area.

16:9

For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.

4:3

Scales the input signal to fit 4:3 display mode in the center of the screen.

LETBOX (Letterbox)

For viewing non-anamorphic (“full-screen”) DVDs on a 16:9 screen.

V-WIDE (VirtualWide)

Enlarges a 4:3 image horizontally in a non-linear fashion to fit 16:9 full screen display.

CINEMA

For viewing 2.35:1 source material.

V-CINE

Selects the Virtual Cinema aspect ratio.

Vistage™ Series Flat-Panel Display Installation/Operation Manual

11

Image 23

Runco V-50HD, V-63HD operation manual Cinema

Contents

Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents External Control Maintenance and TroubleshootingSpecifications Operation List of Figures List of Figures About This Manual Introduction Degrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental information Description, Features and Benefits Optional Accessories Front-Panel Controls IndicatorsControls and Functions Vistage Series at a Glance Remote Control Sensor Primary Input DHD Controller Front Panel DHD Controller Rear Panel Messages from the Hdmi Audio Out connector DHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control Unit For more information about aspect ratios, refer to Table Light Cinema Controls and Functions Installation specialist InstallationRemote Control Operation Quick SetupInstallation Overview Step Procedure For Details, Refer Mounting the V-50HD/V-63HD on a Wall or Table Stand Installation ConsiderationsSynchronization Issues Possible Audio Latency for Various Input Timings Controller Ambient LightOther Considerations Rack-Mounting the DHD DVI-to-HDMI adapters will not work Connecting the DHD Controller to the V-50HD/V-63HDConnections to the V-50HD/V-63HD and DHD Controller Use an Hdmi cable for this connection. a DVI cable with Components to the DHD Connecting Source Component Video Source Connections Rgbhv Source Connections Composite Video Source Connections Controller Optional Connecting an AudioProcessor or Secondary Display Device to the DHD Ethernet Network RS-232 ControllerConnection Connecting to AC Power Turning on the Power Operation Setting the Computer Display Properties Operation Input Position Using the On-Screen Menus Service Aspect Ratio Main MenuInput Source Hdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDs Native Remote Aspect Ratio Control Description Key Picture ScreenPicture Screen Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep Timer System SignalInformation Information Calibration You must enter a passcode to access the Calibration menuCalibration ISF Settings Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copy/Paste Copied settings are not retained after a power cycleMemory Preset Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right Middle Test Patterns and Their Suggested Usage You must enter a passcode to access the Service menuService Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation 38 and ISF Day/Night Memory Presets Regardless of the Logo LED settingRegardless of the Standby LED setting Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting Chart Troubleshooting Chart Serial Communications Port ConfigurationSerial Command Syntax External Control Input Selection Commands Serial Commands Picture Adjust Commands Output Shift Commands Input Position Commands Miscellaneous Commands Screen Commands Exit key Using Discrete IR CodesCommand Parameter min/max Value Stored? Description Enter key With Toggle Bit = Hex Binary Function Start Command Bits RC5 Data Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller ST60MIN Opcode Value Supported? √ = Yes, = No Initiator Follower Using Hdmi CEC MessagesCEC Commands Supported by the DHD Controller Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications 1shows the V-50HD dimensions 50HD Dimensions 2shows the V-63HD dimensions 63HD Dimensions Composite 1 Composite 2 Composite Supported Signal Timings by InputSupported Timings Component Rgbs Format Resolution Frequency Rate Hz MHz KHz PAL-M Specifications Page 020-1114-00 Rev. a April