Remote Aspect Ratio Control Description Key, Native | Runco V-50HD

Operation

Table 4-1. Aspect Ratio Settings (continued)

	Remote
Aspect Ratio	Control			Description
	Key

Cinema	CINEMA					Select Cinema to view 2.35:1
Cinema	CINEMA					Select Cinema to view 2.35:1
						source material on a 16:9
						source material on a 16:9
			2.35:1 Image on			screen. The upper and lower
			2.35:1 Image on			portions of the screen are
			16:9 Screen			portions of the screen are
			16:9 Screen			masked, but the geometry of the
						masked, but the geometry of the
						active image area is not
						changed.
						changed.

Virtual Cinema	V-CINE					A 2.35:1 image is stretched
Virtual Cinema	V-CINE					A 2.35:1 image is stretched
						anamorphically in both
						anamorphically in both
						directions to fill a 16:9 display
			2.35:1 Image on			area.
			16:9 Screen

The 2.35:1 image is cropped on all sides.

2.35:1 Image on 16:9 Screen with Virtual Cinema

Native	NATIVE		Select Native to display the
Native	NATIVE		Select Native to display the
			source signal in its native
			resolution, centered in the
		1080i HDTV Image	display area with no re-sizing or
			overscan.

720p HDTV Image

This means, for example, that 720p HDTV programs will display with unused pixels on all sides: 320 on the left and right sides and 180 above and below.

With SDTV and EDTV sources, the DHD Controller scales the image horizontally to achieve a 16:9 aspect ratio.

Vistage™ Series Flat-Panel Display Installation/Operation Manual

31

Image 43

Runco V-50HD, V-63HD operation manual Remote Aspect Ratio Control Description Key, Native

Contents

Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents External Control Maintenance and TroubleshootingSpecifications Operation List of Figures List of Figures About This Manual Introduction Degrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental information Description, Features and Benefits Optional Accessories Front-Panel Controls IndicatorsControls and Functions Vistage Series at a Glance Remote Control Sensor Primary Input DHD Controller Front Panel DHD Controller Rear Panel Messages from the Hdmi Audio Out connector DHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control Unit For more information about aspect ratios, refer to Table Light Cinema Controls and Functions Remote Control InstallationInstallation specialist Operation Quick SetupInstallation Overview Step Procedure For Details, Refer Mounting the V-50HD/V-63HD on a Wall or Table Stand Installation ConsiderationsSynchronization Issues Possible Audio Latency for Various Input Timings Controller Ambient LightOther Considerations Rack-Mounting the DHD DVI-to-HDMI adapters will not work Connecting the DHD Controller to the V-50HD/V-63HDConnections to the V-50HD/V-63HD and DHD Controller Use an Hdmi cable for this connection. a DVI cable with Components to the DHD Connecting Source Component Video Source Connections Rgbhv Source Connections Composite Video Source Connections Controller Optional Connecting an AudioProcessor or Secondary Display Device to the DHD Connection RS-232 ControllerEthernet Network Connecting to AC Power Turning on the Power Operation Setting the Computer Display Properties Operation Input Position Using the On-Screen Menus Service Input Source Main MenuAspect Ratio Hdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDs Native Remote Aspect Ratio Control Description Key Picture ScreenPicture Screen Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep Timer System SignalInformation Information Calibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right Middle Service You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting Chart Troubleshooting Chart Serial Communications Port ConfigurationSerial Command Syntax External Control Input Selection Commands Serial Commands Picture Adjust Commands Output Shift Commands Input Position Commands Miscellaneous Commands Screen Commands Exit key Using Discrete IR CodesCommand Parameter min/max Value Stored? Description Enter key With Toggle Bit = Hex Binary Function Start Command Bits RC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications 1shows the V-50HD dimensions 50HD Dimensions 2shows the V-63HD dimensions 63HD Dimensions Composite 1 Composite 2 Composite Supported Signal Timings by InputSupported Timings Component Rgbs Format Resolution Frequency Rate Hz MHz KHz PAL-M Specifications Page 020-1114-00 Rev. a April