With Toggle Bit = Hex Binary Function Start | Runco V-50HD, V-63HD

External Control

For example, here is the RC5 control code for the ON button on the DHD Controller remote control unit (assuming the default address is used):

With Toggle Bit = 0

Hex		3			4									4				1

Binary	1		1	0	1		0		0		0		1		0	0	0	0		0	1

						With Toggle Bit = 1

Hex		3			C									4				1

Binary	1		1	1	1		0		0		0		1		0	0	0	0		0	1

Function	Start			Toggle				Address									Command
Function		Bits		Bit				Address									Command
		Bits		Bit

Figure 6-1shows the pulse train for this command (with the toggle bit set to zero).

Data Word

S1

S2

TB

A 4

A 3

A2

A1

A0

C5

C4

C3

C2

C 1

C0

Start Bits Toggle Bit

Address Bits

Command Bits

Encoded

Data

Word

1

1

0

1

0

0

0

1

0

0

0

0

0

1

1.78 ms

Modulated

Carrier

Zoom In

of Carrier

27.8 µs	tp
	3tp

First Packet	Repeated Packet
RC5 Packet
Transmission
14 cycles, 24.9 ms
64 cycles,	113.8 ms

Figure 6-1. RC5 Message Format

Vistage™ Series Flat-Panel Display Installation/Operation Manual

65

Image 77

Runco V-50HD, V-63HD operation manual With Toggle Bit = Hex Binary Function Start, Command Bits

Contents

Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Specifications Maintenance and TroubleshootingOperation External Control List of Figures List of Figures About This Manual Introduction Certain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunction Description, Features and Benefits Optional Accessories Controls and Functions IndicatorsVistage Series at a Glance Front-Panel Controls Remote Control Sensor Primary Input DHD Controller Front Panel DHD Controller Rear Panel Messages from the Hdmi Audio Out connector DHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control Unit For more information about aspect ratios, refer to Table Light Cinema Controls and Functions Installation specialist InstallationRemote Control Installation Overview Quick SetupStep Procedure For Details, Refer Operation Synchronization Issues Installation ConsiderationsPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table Stand Other Considerations Ambient LightRack-Mounting the DHD Controller Connections to the V-50HD/V-63HD and DHD Controller Connecting the DHD Controller to the V-50HD/V-63HDUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not work Components to the DHD Connecting Source Component Video Source Connections Rgbhv Source Connections Composite Video Source Connections Processor or Secondary Connecting an AudioDisplay Device to the DHD Controller Optional Ethernet Network RS-232 ControllerConnection Connecting to AC Power Turning on the Power Operation Setting the Computer Display Properties Operation Input Position Using the On-Screen Menus Service Aspect Ratio Main MenuInput Source Remote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in their Native Remote Aspect Ratio Control Description Key Picture ScreenScreen Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep Timer Information SignalInformation System Calibration You must enter a passcode to access the Calibration menuCalibration ISF Settings Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copy/Paste Copied settings are not retained after a power cycleMemory Preset Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right Middle Test Patterns and Their Suggested Usage You must enter a passcode to access the Service menuService Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation 38 and ISF Day/Night Memory Presets Regardless of the Logo LED settingRegardless of the Standby LED setting Operation Troubleshooting Tips Maintenance and TroubleshootingTroubleshooting Chart Symptom Possible Causes Solution Troubleshooting Chart Serial Command Syntax Port ConfigurationExternal Control Serial Communications Input Selection Commands Serial Commands Picture Adjust Commands Output Shift Commands Input Position Commands Miscellaneous Commands Screen Commands Command Parameter min/max Value Stored? Description Using Discrete IR CodesEnter key Exit key With Toggle Bit = Hex Binary Function Start Command Bits RC5 Data Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller ST60MIN Opcode Value Supported? √ = Yes, = No Initiator Follower Using Hdmi CEC MessagesCEC Commands Supported by the DHD Controller Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications 1shows the V-50HD dimensions 50HD Dimensions 2shows the V-63HD dimensions 63HD Dimensions Supported Timings Supported Signal Timings by InputComponent Composite 1 Composite 2 Composite Rgbs Format Resolution Frequency Rate Hz MHz KHz PAL-M Specifications Page 020-1114-00 Rev. a April