Samsung 760 Series Listening through a Receiver Home theater, Troubleshooting for Anynet+

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.

1Press the TOOLS button.

Press the ENTER button to select Anynet+ (HDMI-CEC).

2Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select On or Off.

3Press the EXIT button to exit.

View TV

Device List

Recording : DVDR

DVDR Operation

Receiver◄ On ►

Setup

➢ If your receiver supports audio only, it may not appear in the device list. Move Adjust Return

➢ The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV.

➢ When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.

➢ When using the WISELINK Pro feature, sound may not output properly through the receiver.

➢ When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS, Preferred language) menus.

➢ If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power failure), the Select Speaker may be set to External Speaker when you turn the TV on again. (see page 32)

Troubleshooting for Anynet+

Symptom	Solution
Anynet+ does not work.	■	Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices
		only.
	■	Connect only one receiver (home theater).
	■	Check if the Anynet+ device power cord is properly connected.
	■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.
	■	Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
	■	Check whether the TV remote control is in TV mode.
	■ Check whether it is Anynet+ exclusive remote control.
	■	Anynet+ doesn’t work in certain situations. (Searching channels, Operating WISELINK)
	■ When connecting or removing the HDMI 1.3 cable, please make sure to search devices
		again or your TV off and on again.
	■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.	■	Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
		(HDMI-CEC) is set to On in the Anynet+ Setup menu.
	■	Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
		button to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+.	■	Select View TV in the Anynet+ menu.
	■	Press the SOURCE button on the TV remote control and select a device other than Anynet+
		menu.
	■ Press CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode.
		(Note that the channel button operates only when an Anynet+ device with a built-in tuner is
		not connected.)
The message Connecting to	■	You cannot use the remote control when you are configuring Anynet+ or switching to a view
Anynet+ device... appears on the		mode.
screen.	■	Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does not play.	You cannot use the play function when Plug & Play is in progress.
The connected device is not	■	Check whether or not the device supports Anynet+ functions.
displayed.	■	Check whether or not the HDMI 1.3 cable is properly connected.
	■	Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
	■	Search Anynet+ devices again.
	■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may
		not support Anynet+ functions.
The TV program cannot be	Check whether the antenna jack on the recording device is properly connected.
recorded.
The TV sound is not output through	Connect the optical cable between TV and the receiver.
the receiver.

English - 128